5010 VIEW DR 2024-04-12 - Laserfiche WebLink

Option Cards 0 • EDWARDS iO Series panels are supported by a complete line RZI16-2 Remote Zone intillgIMIIII of modules and related equipment that enhance performance ,.._,..,-- and extend system capabilities.Option cards plug directly into• , ® M-41414,1 the control panel main circuit board or are connected to it with a ®;14 ribbon cable.After installation,terminals remain accessible.The ' ', cabinet provides ample room for wire routing,keeping wiring neat i ' t 1_ at all times. t i' ..� ,- �•. j, . 1, ' ,Z Single and Dual Loop Controller Cards The i0-SDC1 is a single loop controller card that can be used with The RZI16 2 Addressable Remote Zone Interface Module is an the i064 as a replacement for the standard 64-point loop,or with addressable device that provides connections for sixteen Class B the i01000 as a 250 point expansion module. Initiating Device Circuits and two Class B Supervised Output Circuits.The inputs and outputs can be configured individually The i0-SDC2 is a 500-point dual loop controller card for the for several device types. i01000 that provides two SLC circuits,each with 125 detector addresses and 125 module addresses. It requires 18 consecutive addresses on the Signaling Line Circuit (SLC).Addresses are assigned electronically.There are no address Specifications iO-SDC1 i0-SDC2 switches to set. Device Addresses 01000:one loop,250 i01000:two loops, The RZI16-2 incorporates two 8-segment DIP switches that device addresses 500 device addresses are used to select the Alarm or Supervisory default device type i064:64 addresses for each of the 16 IDC circuits.The module also includes one Wiring Class B or Class A 4-segment DIP switch used to select the default Relay or NAC Operating Voltage 24VDC output device type.Device types other than the default are Operating Current Standby:55 mA Standby:45 mA accomplished through programming. (fully loaded loop) Alarm:80 mA Alarm:70 mA Note:These ratings do not include the use of two-wire smoke modules. RZI16-2 Specifications Communication Line Max.20.6 V peak-to-peak Voltage Voltage 24V/Aux nominal: 24 VDC Terminal Rating 12 to 18 AWG(0.75 to 2.5 mm2) Supervisory current: 250 mA at 24 VDC nominal Circuit Current 0.5 A max. Alarm Current 1000 mA 24V/Aux minimum: 18.4 VDC Max total loop 66 0 24V/Aux maximum: 26.4 VDC resistance NAC1,NAC2 nominal: 24 VDC Max total loop 0.5 µF Current - capacitance Standby current Isolators 64 isolators maximum per loop(total both for 4.7 k EOL(U.S.) 4.8 mA/circuit isolator bases and modules) Standby current for Ground Fault 0 to 5 kfl 3.9 k EOL(Canada) 5.7 mA/circuit Impedance Alarm current Operating 32 to 120°F(0 to 49°C) at nominal voltage 31.1 mA/circuit Environment 0 to 93%noncondensinat 90°F(32° C Relay outputs Quantity 2 Type Rating(pilot duty) Programmable 24 VDC at 2.5 A Input circuit wiring 25 fl per wire SA-ETH Ethernet Interface Card resistance The SA-ETH card provides a Initiating device circuits . standard 10/100 Base Ethernet Quantity 16 network connection for connecting EOL resistor 4.7 kfl(U.S.);3.9 kO Canada to an intranet,a local network,or Zone voltage 22.78 V for 4.7 Id/(U.S.) the Internet.The card can be 22.08 V for 3.9 kO(Canada) -: used to download configuration Alarm current 31.1 mA/channel at nominal voltage programming from the i0-CU to Alarm impedance range <680 0r v - Trouble impedance range >5.55 kf) the panel. Supervised output circuits The Ethernet card is installed on EOL resistor 15 kfl the plastic assembly and connects Quantity 2 to the main circuit board via a Short circuit detection <2.6 kO MEI • Open circuit detection >61.9 kO ribbon cable. Contact ratings 24 VDC at 2.5 A(5 A for two NACs) SA-ETH specifications Compatible cabinets MFC(A),i01000,APS Ethernet 10/100 Base T Operating environment Temperature 32 to 120°F(0 to 49°C) Humidity 0 to 93%RH,noncondensing at 90°F (32°C) Page5of8 E85001-0135 Issue 1.5