2611 ROCKEFELLER AVE 2022 ROCKEFELLER SQUARE 2 Plans 2024-04-26

INSTALLATION AND MAINTENANCE INSTRUCTIONS {( 5yTE,Iq�), SENSOR° crN B300-6 and B300-6-IV 3825 Ohio Avenue,St.Charles,Illinois 60174 1-800-SENSOR2,FAX:630-377-6495 6" Plug-in Detector Bases www.systemsensorcom SPECIFICATIONS Base Diameter: 6.1 inches(155 mm) Base Height: 0.76 inches(19 mm) Operating Temperature: Refer to applicable sensor Operating Temperature Range using the Base/Sensor Cross Reference Chart at systemsensor.com. Electrical Ratings: Operating Voltage: 15 to 32 VDC Standby Current: 170 pA Listings:UL268 BEFORE INSTALLING FIGURE 2.MOUNTING DETECTOR TO BOX Please read the System Smoke Detectors Application Guide, which provides — detailed information on detector spacing,placement,zoning,wiring,and spe- cial applications. Copies of this application guide are available from SystemrC -----, Sensor.NFPA 72 guidelines should be observed. SNAP ON DECORATIVE WIG NOTICE:This manual should be left with the owner/user of this equipment. IMPORTANT:The detector used with this base must be tested and maintained �— regularly following NFPA 72 requirements.The detector should be cleaned at I sc 10% least once a year. i GENERAL DESCRIPTION o o ilf- The B300-6 and B300-6-IV are plug-in detector bases intended for use in an i intelligent system, with screw terminals provided for power (+ and -), and ..\t.f.-, ,-- remote annunciator connections. Communication takes place over the power , o linesRASE (+ and-). DETECTOR BASE TERMINALS NO. FUNCTION 1 Power(-),Remote Annunciator(-) �m 2 I'ower(+) o �0 ., oxu,PoUFcn m 3 Remote Annunciator(+) �a mom. f FIGURE 1.TERMINAL LAYOUT �C-m(� TERMINAL 2 `1 1J C2036-01 O TERMMALI TERMINALS � "'a -� ¢� INSTALLATION AND WIRING GUIDELINES(SEE FIGURE 3) 01 r �t� All wiring must be installed in compliance with all applicable local codes �/ , ',�� and any special requirements of the authority having jurisdiction.Proper wire « 1. gauges should be used.The conductors used to connect smoke detectors to control panels and accessory devices should be color coded to reduce the like- el lihood of wiring errors.Improper connections can prevent a system from re- sponding properly in the event of a fire. For signal wiring(the wiring between interconnected detectors),it is recom- mended that the wire be no smaller than 18 AWG(0.823 mm2).Wire sizes up Ctl127-07 to 12 AWG(3.31 mm2)may be used with the base. MOUNTING This detector base mounts directly to 4-inch square(with and without plaster Make electrical connections by stripping about'/8 inch(10 mm)of insulation rings),4-inch octagon,31/2-inch octagon.and single gang junction boxes.To from the end of the wire(use strip gauge molded in base).Then slide the wire mount,remove the decorative ring by turning it in either direction to unhook under the clamping plate and tighten the clamping plate screw. Do not loop the snaps,then separate the ring from the base. Install the base on the box the wire under the clamping plate. (See Figure 4.) using the screws supplied with the junction box and the appropriate mounting Check the zone wiring of all bases in the system before installing the detec- slots in the base. tors.This includes checking the wiring for continuity,correct polarity,ground Place the decorative trim ring on the base and rotate it in either direction until fault testing and performing a dielectric test. it snaps into place. (See Figure 2.) The base includes an area for recording the zone,address,and type of detec- tor being installed. This information is useful for setting the detector head address and for verification of the detector type required for that location. Once all detector bases have been wired and mounted,and the loop wiring has been checked,the detector heads may be installed in the bases. 1 156-6566-001 11/17/2017