2611 ROCKEFELLER AVE 2022 ROCKEFELLER SQUARE 2 Plans 2024-04-26

TAMPER-RESIST FEATURE FIGURE 5A.ACTIVATE TAMPER-RESIST FEATURE NOTE:Do not use the tamper-resist feature if a removal tool will be used. PLASTIC LEVER The detector base includes a tamper-resist feature that prevents removal of the detector without using a small screwdriver or similar tool. To activate this feature,use needle-nose pliers to break the tab on the detector base as shown in Figure 5A.Then,install the detector. To remove the detector from the base once the tamper-resist feature has been BREAK TAB AT DOTTED LINE BY activated, remove the decorative ring by rotating it in either direction and TWISTING TOWARD CENTER OF BASE pulling it away front the base.Then,insert a small screwdriver into the notch, as indicated in Figure 5B, and press the plastic lever toward the mounting C0130-00 surface before rotating the detector counterclockwise for removal. FIGURE 5B.DETECTOR REMOVAL The tamper-resist feature can be defeated by breaking and removing the plas- USE SMALL-BLADED SCREWDRIVER TO PUSH PLASTIC LEVER IN DIRECTION OF ARROW tic lever from the base. However, this prevents the feature from being used u again. REMOTE ANNUNCIATOR(RA300Z) / \ Connect the remote annunciator between terminals 1 and 3 using the spade lug terminal included.The spade lug terminal is connected to the base term(- C0130-00 ttal as shown in Figure 6. FIGURE S.CONNECTION TO REMOTE ANNUNCIATOR TERMINAL It is not acceptable to have three stripped wires under the same wiring ter- STRIPPED WIRE minal unless they are separated by a washer or equivalent means.The spade / ^ , lug supplied with the model RA100Z is considered an equivalent means.See frl Figure 3 for proper installation. FIGURE 3.TYPICAL WIRING DIAGRAM FOR 2-WIRE LOOP REMOTE CAUTION:DO NOT LOOP WIRE t=t � ANNUNCIATOR UNDER TERMINAL 1 OR 2.BREAK WIRE RUN TO PR �\ \\ MirSUPERVISION OF CONNEOCTIONS. ^,\]��`\�\`{ I\`\\\�\\�l� w / ^—-- WIRE WITH SPADE LUG 05 coil6-00 p..4 („.. -J r$10. W~ Z io :71U / I -- (-) CLASS A OPTIONAL WIRING t+1 CO129-02 FIGURE 4.TERMINAL WIRE INSTALLATION THIS NOT THIS 0 0 C'4973-00 Please refer to insert for the Limitations of Fire Alarm Systems THREE-YEAR LIMITED WARRANTY System Sensor warrants its enclosed smoke detector base to be free front defects in ma- 12220 Rojas Drive,Suite 700,El Paso TX 79936 USA.Please include a note describing the terials and workmanship under normal use and service for a period of three years from malfunction and suspected cause of failure.The Company shall not be obligated to repair date of manufacture. System Sensor makes no other express warranty for this smoke or replace units which are found to be defective because of damage,unreasonable use, detector base.No agent,representative,dealer,or employee of the Company has the au- modifications,or alterations occurring after the date of manufacture.In no case shall the thority to increase or alter the obligations or limitations of this Warranty.The Company's Company be liable for any consequential or incidental damages for breach of this or any obligation of this Warranty shall he limited to the repair or replacement of any part of other Warranty,expressed or implied whatsoever.even if the loss or damage is caused by the smoke detector base which is found to he defective in materials or workmanship the Company's negligence or fault.Some states do not allow the exclusion or limitation of under normal use and service during the three year period commencing with the date of incidental or consequential damages,so the above limitation or exclusion may not apply manufacture.After phoning System Sensor's toll free number 800-SENSOR2(736-7672) to you.This Warranty gives you specific legal rights,and you may also have other rights for a Return Authorization number,send defective units postage prepaid to:Honeywell, which vary from state to state. System Sensor is a registered trademark of Honeywell International.Inc. 2 156-6566-001 ©2017 System Sensor. 11/17/2017