3003 W CASINO RD BLDG 40-92 2024-06-12

FIGURE S.MULTIPLE FAN SHUTDOWN [12.S]DETECTOR CLEANING PROCEDURES (INTERCONNECTION OF D4120'S): Notify the proper authorities that the smoke detector system is undergoing 0120 VAC D4120 0120 VAC D4120 maintenance,and that the system will temporarily be out of service. Disable 0 0 the zone or system undergoing maintenance to prevent unwanted alarms and 10 Q 10 0 possible dispatch of the fire department. 0 (a 0 18 [12.5.1]ALARM TESTS 19 ® 19 ® la. Test/Reset Button-Press and hold the test button located on the power 0 (D0 Q 50 INT/AUX- 6 C,AUXA INT/AUX- 6 C,AURA DET. board cover for at least 2 seconds. 12 INT+ 16 NC,AUXA 12 INT+ 16 NC,AUXA MAX. OR 1s a s ,a lb. M02-04-00 Magnet Test(Magnet sold separately) -Place the painted sur- 11Q 11 O ® 0 s face of the magnet onto the MAGNET TEST location on the sensor cover Q Q 0 0 of unit(Figure 1). O ® 0 ® OR DETECTOR 1 DETECTOR 2 lc. Remote Test Accessory-See list on page 1. SYSTEM CONTROL SYSTEM CONTROL The red alarm LED on the sensor and the power board should latch on, POWER,FAN POWER,FAN as should any accessories (i.e.RA400Z/RA100Z,RTS451/RTS151).Verify CONTROL OR CONTROL OR system control panel alarm status and control panel execution of all in- THERMOSTAT THERMOSTAT H0552-00 tended auxiliary functions(i.e fan shutdown,damper control,etc.). FIGURE 9.MULTIPLE FAN SHUTDOWN(INTERCONNECTION OF D4120 2. The detector must be reset by the system control panel,front cover Test/ TO DH100ACDC): Reset button,or remote accessory. DH100ACDC DH100ACDC 3. To reset using the Test/Reset button on the power board cover simply Press and release. 4. Verify airflow test per Section 7 has been performed. [12.5.2]SMOKE RESPONSE TESTS Da12o To determine if smoke is capable of entering the sensing chamber, visually identify any obstructions. Plug the exhaust and sampling tube holes to pre- vent ducted air from carrying smoke away from the detector head,then blow �Nl smoke such as cigarette, cotton wick, or punk directly at the head to cause an alarm.REMEMBER TO REMOVE THE PLUGS AFTER THIS TEST,OR THE DETECTOR WILL NOT FUNCTION PROPERLY. D4120 [12.5.3]SMOKE ENTRY USING AEROSOL SMOKE H0617-00 This test is intended for low-flow systems (100-500 FPM). If the air speed is greater than 500 FPM,use a conventional manometer to measure differential [11.1]IMPORTANT INTERCONNECTION NOTES: pressure between the sampling tubes,as described in Section 7.1. • When using the interconnect feature, all interconnected units must be Drill a'/a inch hole 3 feet upstream from the duct smoke detector.With the air powered using the same independent supply. handler on,measure the air velocity with an anemometer.Air speed must be • Polarity must be maintained throughout the interconnect wiring. at least 100 FPM.Spray aerosol smoke*into the duct through the'A inch hole Connect the INT+ terminal on unit 1 to the INT+ terminal on unit 2 for five seconds.Wait two minutes for the duct smoke detector to alarm.If the and so on. Similarly, connect the INT/AUX- terminal on unit 1 to the duct smoke detector alarms, air is flowing through the detector. Remove the INT/AUX-terminal on unit 2 and so on. duct smoke detector cover and blow out the residual aerosol smoke from the • Up to 50 D4120 units may be interconnected. chamber and reset the duct smoke detector.Use duct tape to seal the aerosol • Up to 10 DH100ACDC units may be interconnected. Please note that smoke entry hole. each of the 9 DH100ACDC units interconnected can be substituted by *Aerosol smoke can be purchased from Home Safeguard Industries at home- three D4P120 units. Therefore, when using the interconnect feature a safeguard.com, model 25S Smoke Detector Tester, and Chekkit Smoke De- single DH100ACDC can drive either 9 DH100ACDC's or 27 D4120 units. tector Tester model CHEK02 and CHEK06 available from SDi. When used NOTE:Alarm can be reset only at the initiating device and not at the devices properly, the canned smoke agent will cause the smoke detector to go into interconnected. alarm. Refer to the manufacturer's published instructions for proper use of [12]VERIFICATION OF OPERATION the canned smoke agent. [12.1]FIELD SELECTABLE SETTINGS ACAUTION Verify dip switch settings as per Table 2 on Page S. Canned aerosol simulated smoke(canned smoke agent) formulas will vary by [12.2]POWERING THE UNIT manufacturer. Misuse or overuse to these products may have long term ad- Apply 24 VDC power to 9 and 10 terminals on the D4P120 or apply 120 VAC on verse effects on the smoke detector. Consult the canned smoke agent manufac- terminals named 120VAC.See Figure 7 and electrical specifications for details. turer's published instructions for any further warnings or caution statements. [12.3]PERFORM DETECTOR CHECK VERIFY STANDBY AND TROUBLE TEST per Table 3 on page 8.The use of a [12.6]INSTALL THE COVER remote accessory for visible indication of power and alarm is recommended. Install the covers making sure that the cover fits into the base groove.Tighten NOTE:If an instantaneous tamper delay is selected a trouble may be indicated the seven screws that are captured in the covers. with the cover installed. [13]DETECTOR CLEANING PROCEDURES [12.4]SENSITIVITY VERIFICATION Notify the proper authorities that the smoke detector system is undergoing The sensitivity of the sensor is confirmed to be operating within its allowable maintenance,and that the system will temporarily be out of service. Disable range each time the sensor and power board LEDs blink green every 5 sec- the zone or system undergoing maintenance to prevent unwanted alarms and onds.Note in a maintenance condition the sensor LEDs will blink red every 5 possible dispatch of the fire department. seconds and power board will blink amber as depicted in Table 3 on page 8. The maintenance condition indicates that the sensor is operating outside its original factory preset sensitivity and shall be cleaned or replaced.See Section 9 for reference.This is a valid UL test. 6 I56-2967-008R 06-10