3003 W CASINO RD BLDG 40-92 2024-06-12

[13.1]DETECTOR SENSOR With the key switch selected,there is also the capability of obtaining a sen- 1. Remove the sensor to be cleaned from the system. sitivity measurement of the selected sensor using the SENS-RDR sensitivity 2. Remove the sensor cover by pulling outward on each of the four removal reader(sold separately). tabs that hold the cover in place.See Figure 10. FIGURE 11.WIRING DIAGRAMS FOR OPTIONAL ACCESSORIES: 3. Vacuum the screen carefully without removing it. If further cleaning is required continue with Step 4,otherwise skip to Step 7. 15 15 +I 4. Remove the chamber cover/screen assembly by pulling it straight out. ALARM I I LALARIM5. Use a vacuum cleaner or compressed air to remove dust and debris from AUXOUT- �- T- RED the sensing chamber. zo -I zo (-) D4120 MHR/MHW D4120 RA400Z(OPTIONAL) 6. Reinstall the chamber cover/screen assembly by sliding the edge over the DUCT DETECTOR (OPTIONAL)AUDIO DUCT DETECTOR REMOTE(LED) sensing chamber.Turn until it is firmly In place. ALERT ANNUNCIATOR 7. Replace the cover using the holes for the LEDs for alignment and then Ho554-00 P g g FIGURE 12.WIRING DIAGRAM FOR D4120 TO APA151 OR APA451: gently pushing it until it locks into place. APA151/451 D4120 8. Reinstall the detector. 10 O FIELD [13.2]REINSTALLATION O INSTALLED 1. Reinstall the detector in its housing. 19 AUX OUT+ '8 JUMPER COMMON 0-1 AuxouTVA - 2. Restore system power. 1 17 3. Perform Detector Check,Section 12.3. 12 s 4. Notify the proper authorities testing has been completed and the smoke (RED LED)ALARM 2 15 ALARM 16 14 SUP,NO detector system is back in operation. 11 R TEST 3 SUP,C FIGURE 10.DETECTOR SENSOR EXPLODED VIEW: O2 R RESET SENSOR O+ ACC+ 0 COVER O ACC- (GREEN LED)POWER 3 Q O NOTE:WIRING DIAGRAM SHOWN IS FOR D41204-WIRE DUCT SMOKE DETECTOR SYSTEM EQUIPPED WITHOUTA CONTROL PANEL. NOTE:ATROUBLE CONDITION IS INDICATED 110584-02 SENSING BY LOSS OF GREEN LED CHAMBER FIGURE 13.WIRING DIAGRAM FOR D4120 TO RTS451/RTS151/RTS- ~— E SCREEN EN 451KEY/RTS151KEY. SCR COVER RTS451/RTS451KEY D4120 REMOVAL SENSOR 10 TABS CHAMBER Og O FIELD 19 AUX OUT+ 1S INSTALLED FIELD 8 JUMPERS 2 20 AUX OUT ® C1009-00 JUMPER LED 4 O 17 NOTICE: If any unitary packaged air conditioning units are run during the 12 1s 1 drywall installation phase of any building under construction to accelerate (RED LED) 1s ALARM ALARM 14 SUP,No the drying of joint compound,the subsequent sanding of those drywall joints 5 11 RTEST 3 SUP,C and resulting dust may compromise the sensor heads in duct smoke detectors. 3 2 R RESET O 13 To avoid this condition it is recommended that the sensor heads be removed + ACC+ 5 during the construction phase. (GREEN LED) 0 ACC- O POWER s For additional information visit www.systemsensor.com for a detailed techni- FOR RTS451 KEY ONLY WITHOUT A CONTROL PANEL H0582-17 cal bulletin. FIGURE 14.WIRING DIAGRAM: [14]SENSOR REPLACEMENT(PART NO.2D51) 1. Remove the sensor head by rotating counterclockwise. D4120/D4120W/D4P120 RTS2/RTS2-AOS 2. Pull gently to remove it. 3. To replace the sensor head,align the mounting features and rotate clock- AUX OUT(+) (+) AUX wise into place. AUX OUT() (-) AUX [15]OPTIONAL ACCESSORIES ACC (") ( ) ACC [15.1]RTS451/RTS151/RTS451KEY/RTS151KEY REMOTE TEST STATION ACC(+) (+) ACC The RTS451/RTS1 51/RTS451KEY/RTS151 KEY Remote Test Station facilitates test of the alarm capability of the duct smoke detector as indicated in the RTS451/RTS1 51/RTS451 KEY/RTS1 51 KEY manual. The D4120 duct smoke de- tector can be reset by the RTS451/RTS151/RTS451KEY/RTS151KEY. To install NOTE:If polarity of Acc.(+)and Acc.(—)are reversed, the RTS451/RTS151/RTS451KEY/RTS151KEY,connect the device as shown in an Amber LED on sensor 2 of the duct smoke detector Figure 13;wire runs must be limited to 25 ohms or less per interconnecting power board will exist indicating a trouble condition. H0626-01 wire.If a system control panel is used,the panel itself may require testing. [15.2]RTS2/RTS2-AOS MULTI-SIGNALING ACCESSORY The RTS2 and RTS2-AOS multi-signaling accessories are designed for use with InnovairFlex 4-wire conventional duct smoke detectors only. The accessory has two bicolored LEDs that indicate the sensor status of up to two connected duct smoke detectors.The key switch on the unit can be used to select a con- nected duct detector sensor(either sensorl or sensor 2),and the selected sen- sor can be tested or both sensors can be reset simultaneously using the test/ reset button. LED status indications include: Standby (green blink), Trouble (amber),Maintenance(amber blink)and Alarm(red). 7 I56-2967-008R 06-10