Laserfiche WebLink
�UVLaK' <br />� MML <br />FIG. i402 <br />S1ideLOK® Ready for Installation Coupling <br />FIGURE <br />7402 SLIDELOKCOUPLING <br />Nominal <br />Max. Working <br />Max. <br />Range of <br />Coupling Dimensions <br />Coupling Bolts <br />Specified Torque § <br />Approx. Wt. <br />Size <br />C.D. <br />Pressure t <br />Entl Load <br />Pipe End <br />Separation <br />Ea. <br />Xa <br />Xb <br />Y <br />Z <br />oty. <br />Size <br />Min. Max <br />INON(mm) <br />INmm <br />PSYb. <br />LhsAW <br />In <br />INmm <br />INmm <br />In/mm <br />In/mm <br />In <br />FL-Lbs/N-M <br />Lb,Ag <br />2 <br />2.375 <br />750 <br />3,323 <br />0-Ys2 <br />3'/4 <br />3'/e <br />6 <br />2 <br />2 <br />Y2 x 2%4 <br />80 <br />100 <br />2.9 <br />59 <br />69.3 <br />51.7 <br />14,78 <br />9-9.79 <br />95 <br />86 <br />152 <br />51 <br />M12x79 <br />110 <br />150 <br />1.3 <br />21/2 <br />2.875 <br />750 <br />4,869 <br />0-1/32 <br />4'/e <br />4Y4 <br />6% <br />2 <br />2 <br />Y2 x 2%4 <br />80 <br />100 <br />3.1 <br />65 <br />73.9 <br />51.7 <br />21,66 <br />9-9.79 <br />117 <br />108 <br />163 <br />51 <br />M12x79 <br />110 <br />150 <br />1.4 <br />3 <br />3.500 <br />750 <br />7,216 <br />0-1/32 <br />5Y5 <br />4"/a <br />7 <br />2 <br />2 <br />Y2x3Y2 <br />80 <br />100 <br />3.6 <br />89 <br />88.9 <br />51.7 <br />32,10 <br />9-9.79 <br />132 <br />119 <br />178 <br />51 <br />M12x89 <br />119 <br />150 <br />1.6 <br />4 <br />4.500 <br />750 <br />11,928 <br />0-%32 <br />6Y2 <br />6 <br />85/ a <br />2 <br />2 <br />Y2 x 31/2 <br />80 <br />100 <br />4.9 <br />100 <br />1141 <br />51.7 <br />53,06 <br />9-2,38 <br />165 <br />152 <br />212 <br />51 <br />M12x89 <br />110 <br />150 <br />22 <br />5 <br />5.563 <br />750 <br />18,229 <br />0-%32 <br />7'/4 <br />7T/a <br />9%4 <br />2 <br />2 <br />s/a x 31/2 <br />100 <br />130 <br />6.1 <br />125 <br />141.3 <br />51.7 <br />81,09 <br />9-2,38 <br />196 <br />181 <br />248 <br />51 <br />M16x89 <br />135 <br />175 <br />28 <br />6 <br />6.625 <br />700 <br />24,130 <br />0-%32 <br />81/a <br />8Y5 <br />104/5 <br />2 <br />2 <br />c/a x 31/2 <br />100 <br />130 <br />6.8 <br />150 <br />168.3 <br />48.3 <br />107.34 <br />9-2,38 <br />224 <br />298 <br />274 <br />51 <br />M16x89 <br />135 <br />175 <br />3.1 <br />8 <br />8.625 <br />600 <br />35,056 <br />0-%32 <br />113/8 <br />10'/a <br />132/s <br />21/2 <br />2 <br />a/4 x 41/2 <br />130 <br />180 <br />10.9 <br />200 <br />2194 <br />41.4 <br />15594 <br />9-2,38 <br />289 <br />270 <br />340 <br />64 <br />M29x115 <br />175 <br />245 <br />ell <br />NOTES: <br />For additional details see Coupling Data Chart Notes" In the Introduction Section of the Orders Catalog. <br />Range of Pipe End Separation values are for roll grooved pipe and may be doubled for cut groove pipe. <br />§— For additional Bolt Torque Information, see the Technical Data Section of the Curves Catalog. <br />t Maximum Working Pressure Rating is for schedule 40 steel pipe. For light wall, stainless steel, aluminum and ISO pipe <br />See Installation&Assembly directions on next page. <br />pressure ratings, please refer to the technical data section. <br />Notfor use In copper systems. <br />impact gun can se uoca for installation p we ur that the output of t e impact pact gun is within the required ca torque i a iuc. <br />Not for use on "EG" rolled or cut showed pipe ends. <br />Contact an Anvil Representative for use on light wall and SS pipe applications. <br />GL-5.16 <br />