1105 13TH ST 2024-06-07 - Laserfiche WebLink

TFP172 Page 3 of 4 Sprinkler Fmish8 K-Factor Type Temperature Bulb Liquid Color Natural Brass Chrome Plated polyester= 135°F (57°C) Orange UPRIGHT (TY313) 155°F(68°C) Red 175°F (79°C) Yellow and 1, 2, 3, 4, 5, 6, 7 PENDENT (TY323) 200°F (93°C) Green 5.6 1/2 in. NPT 286-F(141°C) Blue 135°F (57°C) Orange RECESSED PENDENT (TY323) Figures 4- and 56 1 2 3 4 7 ° 155F (68°C) Red 175°F (79°C) Yellow 200°F (93°C) Green Notes: 1. Listed by Underwriters Laboratories Inc (UL) as Quick Response Sprinklers. 2. Listed by Underwriters Laboratories Inc for use in Canada(C-UL) as Quick Response Sprinklers. 3. Approved by Factory Mutual Research Corporation(FM) as Quick Response Sprinklers. 4. Approved by the City of New York under MEA354-01-E. 5. VdSApproved(For details , contact Johnson Controls, Enschede, Netherlands ,Tel .3153-428-4444/Fax 3154-428-3377) 6. Approved by the Loss Prevention Certification Board (LPCBRef .No.094a/06) as Quick Response Sprinklers. 7 EAC Approved 8. Where Polyester Coated Sprinklers are noted to be UL and C-ULListed the sprinklers are UL and C-UL Listed as Corrosion -Resistant Sprinklers. a Installed with Style 15 (1/2 in.NPT)5/8in. Total Adjustment Recessed Escutcheon, as applicable. b. Installed with Style 20 (1/2 in NPT) 1/2 in. Total Adjustment Recessed Escutcheon, as applicable. c. Frame and Deflector only Listings and approvals apply to color (Special Order). TABLE A LABORATORY LISTINGS AND APPROVALS FOR 5.6 K-FACTOR SPRINKLERS Operation The glass bulb contains a fluid which expands when exposed to heat. When the rated temperature is reached, the fluid expands sufficiently to shatter the glass bulb, allowing the sprinkler to activate and water to flow. Design Criteria The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers are intended for fire protec- tion systems designed in accordance with the standard installation rules recognized by the applicable Listing or Approval agency (such as, UL Listing is based on the requirements of NFPA 13, and FM Approval is based on the requirements of FM's Loss Prevention Data Sheets). Only the Style 15 or Style 20 Recessed Escutcheon is to be used for recessed pendent installations. Installation The TYCO Series TY-FRB, 5.6 K-factor, Upright (TY313) and Pendent (TY323) Sprinklers must be installed in accor- dance with this section. General Instructions Do not install any bulb -type sprin- kler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprinkler held horizontally, a small air bubble should be present. The diam- eter of the air bubble is approximately 1/16 in. (1,6 mm) forthe 135°F (57°C) and 3/32 in. (2,4 mm) for the 286°F (141°C) temperature ratings. A leak -tight 1/2 in. NPT sprinkler joint should be obtained by applying a minimum to maximum torque of 7 to 14 lb-ft (9,5 to 19,0 N-m). Higher levels of torque can distort the sprinkler Inlet with consequent leakage or impairment of the sprinkler. Do not attempt to compensate for insufficient adjustment in the Escutch- eon Plate by under- or over -tightening the sprinkler. Re -adjust the position of the sprinkler fitting to suit. Upright and Pendent Sprinklers The Series TY-FRB Upright and Pendent Sprinklers must be installed in accordance with the following instructions. Step 1. Install Pendent sprinklers in the pendent position. Install upright sprin- klers in the upright position. Step 2. With pipe -thread sealant applied to the pipe threads, hand - tighten the sprinkler into the sprinkler fitting. Step 3. Tighten the sprinkler into the sprinkler fitting using only the W-Type 6 Sprinkler Wrench as shown in Figure 2. Apply the W-Type 6 Sprinkler -Wrench to the wrench flats as shown in Figure 1. Torque sprinklers 7 to 14 lb-ft (9,5 to 19,0 N m). Recessed Pendent Sprinklers The Series TY-FRB Recessed Pendent Sprinklers must be installed in accor- dance with the following instructions. Step A. After installing the Style 15 or Style 20 Mounting Plate over the sprinkler threads, and with pipe -thread sealant applied to the pipe threads, hand -tighten the sprinkler into the sprinkler fitting. Step B. Tighten the sprinkler into the sprinkler fitting using only the W-Type 7 Recessed Sprinkler Wrench as shown in Figure 3. Apply the W-Type 7 Recessed Sprinkler Wrench to the sprinkler wrench flats as shown in Figure 1. Torque sprinklers 7 to 14 lb-ft (9,5 to 19,0 N-m). Step C. After ceiling installation and finishing, slide on the Style 15 or Style 20 Closure over the Series TY-FRB Sprinkler and push the Closure overthe Mounting Plate until its flange comes in contact with the ceiling.