Laserfiche WebLink
• f <br /> Complete Connection <br /> 1. Check that the gas pressure regulator shutoff valve is in the Verify Anti-TipBracket is installed and <br /> "on"position. Engaged <br /> On Ranges with a Storage Drawer: <br /> 01. Remove the storage drawer.See"Storage Drawer"section. <br /> �-�. 2. Use a flashlight to look underneath the bottom of the range. <br /> 3. Visually check that the rear range foot is inserted into the slot <br /> j .,Ceof the anti-tip bracket. <br /> On Ranges with a Warming Drawer or Premium Storage <br /> A Drawer: <br /> A.Gas pressure regulator shutoff valve 1. Place the outside of your foot against the bottom front of the <br /> shown In the"on"position warming drawer or premium storage drawer,and grasp the <br /> lower right or left side of the control panel as shown. <br /> 2. Open the manual shutoff valve in the gas supply line.The NOTE:If your countertop is mounted with a backsplash,it <br /> valve is open when the handle is parallel to the gas pipe. may be necessary to grasp the range higher than is shown in <br /> A- the illustration. <br /> 8 ► <br /> s.4110A( <br /> A.Closed valve <br /> B.Open valve 11.00 <br /> 3. Test connections by brushing on an approved � <br /> noncorrosive leak-detection solution.If bubbles appear,a We- <br /> leak is indicated.Correct any leak found. Alt <br /> 4. Remove cooktop burner caps and grates from parts • , - <br /> package.Burner caps should be level when properly fclUt <br /> �v•positioned.If burner caps are not properly positioned, • l `-� <br /> surface burners will not light.Place burner grates over 1I) <br /> burners and caps. '- <br /> B' 0'-,'.:t.••.•.i...;i) <br /> __ <br /> A C 1 1 <br /> •-• <br /> . \ <br /> A.Burner base 2. Slowly attempt to tilt the range forward. <br /> B.Burner cap If you encounter immediate resistance,the range foot is <br /> C.Burner grate <br /> engaged in the anti-tip bracket. <br /> 3. If the rear of the range lifts more than 1"(1.3 cm)off the floor <br /> without resistance,stop tilting the range and lower it gently <br /> a WA R N I N G back to the floor.The range foot is not engaged in the anti-tip <br /> bracket. <br /> IMPORTANT:If there is a snapping or popping sound when lifting <br /> the range,the range may not be fully engaged in the bracket. <br /> Check to see if there are obstructions keeping the range from <br /> III sliding to the wall or keeping the range foot from sliding into the <br /> bracket.Verify that the bracket is held securely in place by the <br /> Electrical Shock Hazard mounting screws. <br /> 4. Slide the range forward,and verify that the anti-tip bracket is <br /> Plug into a grounded 3 prong outlet. securely attached to the floor or wall. <br /> Do not remove ground prong. 5. Slide range back so the rear range foot is inserted into the <br /> slot of the anti-tip bracket. <br /> Do not use an adapter. IMPORTANT:If the back of the range is more than 2"(5.1 cm) <br /> Do not use an extension cord. from the mounting wall,the rear range foot may not engage the <br /> Failure to follow these instructions can result in death, bracket.Slide the range forward and determine if there is an <br /> obstruction between the range and the mounting wall.Changes <br /> fire,or electrical shock. to the gas supply must be performed by a qualified service <br /> technician.If you need assistance or service,refer to the <br /> 5. Plug into a grounded 3 prong outlet. "Assistance or Service"section of the Use and Care Guide,or the <br /> 6. Slide range into final location,making sure the rear leveling cover or"Warranty"section of the User Instructions,for contact <br /> leg slides into the slot of the anti-tip bracket. information. <br /> 9 <br />