3201 SMITH AVE BASE FILE 2024-10-14

s Si m plex TrueAlarm Analog Sensing UL, ULC,CSFM Listed,-FM TrueAlarm Analog Sensors- Photoelectric and Heat; Standard Bases and Accessories Approved;MEA(NYC) Acceptance* Features condition is determined by comparing the sensor's present value against its average value and time. TrueAlarm analog sensing provides: • Digital transmission of analog sensor values via IDNet or MAPNET II Intelligent Data Evaluation. two-wire communications Monitoring each sensor's average value provides a continuously shifting reference point.This software filtering process compensates for For use with the following Simplex products: environmental factors(dust,dirt,etc.)and component aging,providing 4007ES,4010,4010ES,4100ES,and 41000 Series control panels;and an accurate reference for evaluating new activity.With this filtering,there 4008 Series control panels with reduced feature set(refer to data is a significant reduction in the probability of false or nuisance alarms sheet S4008-0001 for details) caused by shifts in sensitivity,either up or down. 4020,4100,and 4120 Series control panels,Universal Transponders, Control Panel Selection. and 2120 TrueAlarm CDTs equipped for MAPNET II operation Peak activity per sensor is stored to assist in evaluating specific locations. Fire alarm control panel provides: The alarm set point for each TrueAlarm sensor is determined at the Peak value logging allowing accurate analysis of each sensor for host control panel,selectable as more or less sensitive as the individual individual sensitivity selection application requires. Sensitivity monitoring satisfying NFPA 72 sensitivity testing requirements;automatic individual sensor calibration check verifies sensor integrity II Automatic environmental compensation,multi-stage alarm operation, and display of sensitivity directly in percent per foot Ability to display and print detailed sensor information in plain English language Photoelectric smoke sensors provide: • Seven levels of sensitivity from 0.2%to 3.7%(refer to additional Figure 1: 4098-9714 TrueAlarm information on page 3) Photoelectric Sensor Mounted in Base Heat sensors provide: Timed/Multi-Stage Selection. Three fixed temperature sensing thresholds:135°F,155'F and 190'F Sensor alarm set points can be programmed for timed automatic Rate-of-rise temperature sensing sensitivity selection(such as more sensitive at night,less sensitive during day).Control panel programming can also provide multi-stage operation Utility temperature sensing per sensor.For example,a 0.2%level may cause a warning to prompt Listed to UL 521 and ULC-5530 investigation while a 2.5%level may initiate an alarm. General features: Sensor Alarm and Trouble LED Indication. Operation is for ceiling or wall mounting Each sensor base's LED pulses to indicate communications with the Listed to UL 268 and ULC-5529 panel.If the control panel determines a sensor is in alarm,or is dirty NEMA 1 rated.See TrueAlarm Analog Sensing Product Selection Chart or has some other type of trouble,the details are annunciated at the for more information. control panel and that sensor base's LED will be turned on steadily. Louvered smoke sensor design enhances smoke capture by directing During a system alarm,the control panel will control the LEDs such that flow to chamber;entrance areas are minimally visible when ceiling an LED indicating a trouble will return to pulsing to help identify the mounted alarmed sensors. Designed for EMI compatibility Sensor Base Features Magnetic test feature is provided Different bases are available to support a supervised or unsupervised Base mounted address selection: output relay,and/or a remote LED alarm indicator Address remains with its programmed location Additional base reference: Accessible from front(DIP switch under sensor) For isolator bases,refer to data sheet 54098-0025 General features: For sounder bases,refer to data sheet 54098-0028 Automatic identification provides default sensitivity when substituting For photo/heat sensors,refer to data sheet 54098-0024(single sensor types address)and 54098-0033(dual address) Integral red LED for power-on(pulsing),or alarm or trouble(steady on) Locking anti-tamper design mounts on standard outlet box Description Magnetically operated functional test Digital Communication of Analog Sensing. TrueAlarm analog sensors provide an analog measurement digitally communicated to the host control panel using Simplex addressable communications.At the control panel,the data is analyzed and an average value is determined and stored.An alarm or other abnormal *These products have been approved by the California State Fire Marshal(CSFM)pursuant to Section 13144.1 of the California Health and Safety Code.See CSFM Listings 7272-0026:218, 7271-0026:231,7270-0026:216,and 7300-0026:217 for allowable values and/or conditions concerning material presented in this document.Accepted for use-City of New York Department of Buildings-MEA35-93E.Additional listings may be applicable,contact your local Simplex product supplier for the latest status.Listings and approvals under Simplex Time Recorder Co.are the property of Tyco Fire Protection Products. 54098-0019 Rev. 25 01/2020