11802 EVERGREEN WAY WOODS COFFEE 2024-10-11

Application Installation Genesis strobes are UL 1971-listed for use indoors as wall-mount- Genesis horns and strobes mount to any standard one-gang sur- ed public-mode notification appliances for the hearing impaired. face or flush electrical box. Matching optional trim plates are used Prevailing codes require strobes to be used where ambient noise to cover oversized openings and can accommodate one-gang, conditions exceed 105 dBA(87dBA in Canada),where occupants two-gang,four-inch square, or octagonal boxes,and European use hearing protection,and in areas of public accommodation 100 mm square. as defined in the Americans with Disabilities Act(see application notes—USA). All Genesis signals come pre-assembled with captive mounting screws for easy in- Combination horn-strobe signals must be installed in accordance stallation.Two tabs at the top of the signal with guidelines established for strobe devices.Consult with your unlock the cover to reveal the mounting Authority Having Jurisdiction for details. . hardware.The shallow depth of Genesis All Genesis strobes exceed UL synchronization requirements devices leaves ample room behind the (within 10 milliseconds over a two-hour period)when used with a signal for extra wiring.Once installed with synchronization source. Synchronization is important in order to emu` the cover in place, no mounting screws avoid epileptic sensitivity. are visible. WARNING:These devices will not operate without electrical power.As fires frequently cause power interruptions, further safeguards such as Genesis Horn/Strobe Field Configuration backup power supplies may be required. with optional trim Temporal horn and horn-strobe models plate are factory set to sound in a three-pulse temporal pattern. Units may be con- figured for use with coded systems by cutting a jumper on the Horns circuit board.This results in a steady output that can be turned Genesis horn output reaches as high as 99 dB and features a on and off(coded)as the system applies and removes power to unique multiple frequency tone that results in excellent sound the signal circuit.A Genesis Signal Master is required when horn- penetration and an unmistakable warning of danger. Horns may be strobe models are configured for coded systems. Non-temporal, configured for either coded or non-coded signal circuits.They can horn-only models sound a steady tone. also be set for low dB output with a jumper cut that reduces horn Genesis clear strobes and horn-strobes are shipped from the fac- output by about 5 dB. Horn-only models may be ceiling-mounted tory ready for use as UL 1971 compliant signals for public mode or wall-mounted. operation.These signals may be configured for temporal flash by The suggested sound pressure level for each signaling zone used with cutting a jumper on the circuit board.This battery-saving feature is alarm signals is at least 15 dB above the average ambient sound level, intended for private mode signaling only. or 5 dB above the maximum sound level having a duration of at least Genesis clear strobes and horn-strobes may be set for 15,30,75, 60 seconds,whichever is greater,measured 5 feet(1.5 m)above the or 110 candela output.The output setting is changed by simply floor.The average ambient sound level is,A-weighted sound pressure opening the device and sliding the switch to the desired setting. measured over a 24-hour period. The device does not have to be removed to change the output Doubling the distance from the signal to the ear will theoretically result setting.The setting remains visible through a small window on the in a 6 dB reduction of the received sound pressure level.The actual side of the device after the cover is closed. effect depends on the acoustic properties of materials in the space. Horns and horn-strobes are factory set for high dB output. A 3 dBA difference represents a barely noticeable change in volume. Low dB output may be selected by cutting a jumper on the circuit board.This reduces the output by about 5 dB. Wiring Field wiring terminals accommodate#18 to#12 AWG(0.75 mm2 to 2.5 mm2)wiring. Horns, strobes,and combination horn-strobes are interconnected with a single pair of wires as shown below. + + To next appliance, Polarity shown in end-of-line alarm condition H H or return to control equipment ONote:Strobes must have continuous voltage. Page 2 of 6 DATA SHEET S85001-0573 Not to be used for installation purposes. Issue 11.1