3003 W CASINO RD BLDG 45-715 2024-12-05

~E _ P 1. 4"(10.2 cm.) _ square box 2-1/8" 0 (5.4 cm.)back box -� 2 -gang b ornck double I -gang back box 3� 3® 3. 5"(12.7 cm.) square switch plate,(supplied) Intelligent Device Interface Module Specifications —(continued' Mounting Data Model XTRI-R PROGRAMMING HOLES NOTES: Each interface module mounts directly to a user- Through the use of an add ressable'Form C' relay, the r, ,-,� - supplied switchbox. Model XTRI-R relay and contact device input are ® The electrical boxes, seen controlled at the same address. The relay and input above, are supplied-by-others contact can be controlled as a separate function from a (130). Siemens compatible FRCP. The relay is typically used SLOT FOR Models XTRI-D, XTRI-R and XTRI-S where control or shunting of external equipment is LOCATING mount directly onto a 4-inch (10.2 cm.; required. TAB square, 2 'V (5.7 cm.)-deep box back box, or to a user-supplied double-gang 3 Model XTRI-D /2"deep back box. Model XTRI-D is a dual-input modulethat is designed I THERE IS NO DIRECTIVITY to supervise and monitor two(2)sets of drycontacts. DESIGN FORDPU11 , A5"(12.7 cm.)square, off-white faceplate Model XTRI-D only requires one (1) address, but CONNECTION.IT T_ PLUG FROM is included in each shipment of a Siemens IS ALLOWED TO THE DPU responds independently to each input. Model XTRI-D INSERT THE PLUG PROGRAMMER; Model XTRI-series module. is ideal for monitoring a water-flow switch and its AT EITHER DIRECTION TESTER respective valve tamper switch. F671"rym, Field-Device Programmer/Test Unit Siemens—Fire Safety innovative technology allows Model XTRI-series intelligent interface modules to be programmed via the Siemens field-device programmer I test unit (Model DPU), which is a compact, portable and menu-driven accessory for electronically programming and testing Siemens peripheral modules and devices promptly and reliably. For instance, the field technician selects the accessory's program mode, and enters the desired address. Model XTRI-series interface module is connected to Model DPU with the programming cable provided with the tester. NOTE: Since the XTRI-series of interface modules are advanced initiating devices, the latest Model DPU firmware update is required. Model DPU eliminates the need for cumbersome, unreliable mechanical programming methods (e.g. — dials and rotary switches), and reduces installation and service costs by electronically programming and testing the module prior to installation. When set in 'test' mode, Model DPU will perform a series of diagnostic tests without altering the address or other stored data, allowing technicians to determine if the module is operating properly. Each field-device programmer / test unit operates on AC power or rechargeable batteries, providing flexibility and convenience in the programming/testing of fire-safety equipment from practically any location. Additionally,with the use of a Model DPU unit,there is no longer a cause for concern with any vibration,corrosion and other deteriorating conditions that could negatively affect any electro-mechanical-addressing mechanism. Compatibilities Siemens 'X'modules may be used along with Model 'H'-series intelligent detectors; Model 'HMS'-series addressable manual stations,or any other 'H'-series addressable intelligent module(e.g. Model HZM or Model HCP). Additionally the X- series modules are compatible with all Desigo and Cerberus Pro detectors and peripherals of the same circuit. Interspersing 'X'& 'H'-series devices on the same loop is mostly permitted,but there are exceptions: Models HUM(isolation module) and SBGA-34 (audible base) cannot be used with 'X'devices on the same loop. Siemens Smart Infrastructure— Building Products —2— usa.siemens.com/fire