3625 BROADWAY SONIS KITCHEN 2025-01-03

GENERAL CONSTRUCTION NOTES 1. The General Contractor shall provide building penetrations, roofing, and other IMC 2018 SECTION 507.1.1 ❑PERATION. (PARTIAL) construction needs for installation of system equipment. THE EXHAUST FAN SERVING A TYPE I HOOD SHALL HAVE AUTOMATIC CONTROLS THAT WILL ACTIVATE THE FAN WHEN ANY APPLIANCE THAT REQUIRES SUCH TYPE I HOOD 2. The General Contractor shall be responsible for Maintaining structural integrity and IS TURNED ON, OR A MEANS OF INTERLOCK SHALL BE PROVIDED THAT WILL PREVENT provide required structural supports as required City of Everett. OPERATION OF SUCH APPLIANCES WHEN THE IS NOT TURNED ON.. 3. The General Contractor shall be responsible for other trades unless otherwise stated by the conditions of the general contract with the project owner. TYPE I EXHAUST AIR DUCTWORK TO BE MAKE-UP AIR DUCTWORK TO BE FULLY WELDED 16 GAUGE STEEL FULLY SEALED 22 GAUGE STEEL EXHAUST SYSTEM NOTES REVISIONS: DUCTWORK TO BE CONTINUOUS INTERNAL MAKE-UP AIR DUCTWORK TO BE INSULATED 1. The exhaust/make-up air systems are to meet requirements of the International Mechanical Code, OR EXTERNAL LIQUID-TIGHT WELDED and NFPA-96. The Type I exhaust ductwork to be constructed of fully welded 16 gauge steel. SMOOTH, ACCESSIBLE FOR INSPECTION, AND WITHOUT GREASE TRAPS 2. Exhaust must be a minimum of 10'-0' from any air intake, adjacent building, or adjoining property. 3. Exhaust and make-up air systems must be electrically interconnected to be operated simultaneously by a single on/off switch. ELECTRICAL NOTES FAN BASE 1. The electrical contractor shall provide and Install Interconnecting field wiring between the z hood equipment control switches, and exhaust / make-up air system equipment contactors. 2. The electrical contractor shall install exhaust fan and make-up air system motor relays a and disconnect switches. w 3. The electrical contractor shall verify proper fan motor rotation, cai TYPICAL HINGE KIT a EQUIPMENT CURB z EF-1 TYPE I EF-1 TYPE I 0 EXHAUST FAN 120" EXHAUST FAN J O MUA-1 MAKE-UP MUA-1 MAKE-UP > AIR FAN AIR FAN w Q 00 5 _ � o ra Q 3 439. 439, 0 16 16 / MUA-1 MAKE-UP \ I--I AIR UNIT ON ROOF (o z 18" 18' o ate-+ a L m Ln m / EF-1 TYPE I O (1J L J EXHAUST FAN EH-1 TYPE I CLEAN-OUT w (n LD > ACCESS I ON ROOF EXHAUST HOOD CLEAN-OUT / FIRE RATED 10'-0' ❑14'x14" SLOPE DUCT ❑ ACCESS 16'x16' 14"x14' / DUCT WRAP MINIMUM TO J i ANY AIR INTAKE F FIRE RATED Li DUCT WRAP 0 16'x16'019'-6' °�' ABOVE r-1 GROUND o 18" LEVEL o _ / ^. ro N 24"ZVV EH-1 TYPE I EXHAUST HOOD — Q 3+ 6" EH-1 TYPE I 6" 3' o a EXHAUST HOOD 18' 18" 51' N o ONE HOUR FIRE 52" 2 r co RATED WALL PAD 44' a COOKING 6' w EQUIPMENT MIN z UD 80' I F `o co 00 00 00 00 0o ONE HOUR o o U'� FIRE RATED CO WALL PAD c U O < co P DRAWN BY: DOUG WALTER UPDATE: 04/11/2024 ELEVATION 0 Scale 3/8"= 1'-0" TITLE: COMMERCIAL KITCHEN EXHAUST SYSTEM TYPE I EXHAUST AND MAKE-UP AIR SYSTEM EQUIPMENT SCHEDULE PLAN VIEW NORTH City of Everett Permit Review J.H11T1YZPr= M HOOD CAPTURE SIZE HOOD EXHAUST EXHAUST EXHAUST EXHAUST EXHAUST FAN MAKE-UP MAKE-UP MAKE-UP MAKE-UP MAKE-UP AIR FAN SHEET WEIGHT DUCT DUCT AIR DUCT DUCT AIR DUCT DUCT EVERETT Status:Reviewed TOT Permit WITH SIZE WEIGHT CFM VELOCITY FAN MAKE MODEL CFM HP ESP POWER RPM FAN SQE CFM VELOCITY WEK#iT FAN MAKE MODEL HP ESP PO RPM MBTU'S UNIT C� 04/16/2024 9:28:58 AM WITH WEIGHT WEIGHT Scale 1/4"— 1'-0" M—2 8'-a'X 4'-6'CANOPY GREASE HOOD ZI 1SS 14'x14' 185 LBS 2000 CFM 1471 FPM EF-1 ACCUREX XRUD-140-VG 2000 1.0 1.448 115/1 1688196 LBS IV.16' 1800 CFM 1017 RPM 200 LSS MUA-1 ACCUREX XDGX-PBS-H05-VFD 1 1.5 1AW 208/3 1002 85.5 398 LR3 �D I