Laserfiche WebLink
RXK Series Scissor Lift Racks <br /> Table of Contents <br /> 1. For Your Safety 5 <br /> 1.1. Corporate Information 5 <br /> 1.2. Hazard Definitions 5 <br /> 1.3. RXK Power Requirements 6 <br /> 1.3.1. Intrinsically Safe Circuit 6 <br /> 1.4. RXK Air Requirements 6 <br /> 1.5. RXK Grout Requirements 6 <br /> 1.6. Surface Mount Rack Site Verification 6 <br /> 1.7. Flush Mount Site Verification 8 <br /> 1.8. Domestic Product Support 8 <br /> 1.9. International Support Documents 8 <br /> 2. Centerline Reference Diagram 9 <br /> 2.1. Centerline Reference 10 <br /> 2.2. Centerline Reference-BMW&MB 10 <br /> 3.Bay Layout Preparation 11 <br /> 3.1. Establish Installation Centerline 11 <br /> 3.2. Establish the Rear Location of the Ramps(Surface Mount Only) 11 <br /> 3.3. Establish the Front Location of the Runways(Surface Mount Only) 11 <br /> 4. Frame&Console Reference 12 <br /> 4.1. Frame&Console Reference 13 <br /> 4.2. BMW&MB Reference 13 <br /> 4.3. Establish the Interior Edge Location of the Base Frames-Letter F 13 <br /> 4.4. Establish the Rear Location of the Base Frames-Letter G(Surface Mount Only) 13 <br /> 4.5. Establish the Console Centerline and Outside Edge Line-Letter E(Surface Mount Only) 13 <br /> 5. Positioning the Runways 14 <br /> 5.1. Ramp Spacing 14 <br /> 5.2. Ramp Spacing BMW&MB 14 <br /> 5.3. Ramp Spacing 15 <br /> 6. Runways&Console 16 <br /> 6.1. Open Control Console 16 <br /> 6.1.1.Check.Jumper Settings 16 <br /> 6.1.2.(S3-S14)Jumper Settings 17 <br /> 6.1.3. Inflation Station&Flush Mount Jumpers 17 <br /> 6.1.4.J1 &Customized Jumper Settings 18 <br /> 6.1.5. (S30)Jumper Setting 18 <br /> 6.1.6. Other Jumpers 18 <br /> 6.2. Control Console Positioning 19 <br /> 6.2.1.Standard Console Placement 19 <br /> 6.2.2:Non-Standard Console Placement-Additional Threshold 19 <br /> 6.3. Hydraulic Hose Connections 20 <br /> 6.4. Fill Hydraulic Reservoir 20 <br /> 7. Connect Console Power 21 <br /> 7.1•. Overload Relay 21 <br /> 8.Swing Air Jack Install 22 <br /> 8.1. Front of Runways 22 <br /> 8.2. Rear of Runways 22 <br /> 9. Pneumatic Diagram 23 <br /> 10.Air Line Installation 24 <br /> •10.1;Air Line Routing 24 <br /> 10.2. Routing at Runway Base 25 <br /> 10.3. Lock Release Air Line 26 <br /> 10.4.Jack Air Supply&Quick Disconnects 27 <br /> 10.4.1.Front of the Left(Driver Side)Runway 28 <br /> 10,4.2.Rear of the Left Runway 28 <br /> 10.4.3.Center of Left Runway 28 <br /> 10.5. PowerSlide 28 <br /> 10.5.1.PowerSlide Turnplates Air Supply 29 <br /> 10.6. Inflation Station(optional feature) 29 <br /> 11.Console Part 2 31 <br /> 11.1. Connect Air Lines to Console 31 <br /> Page 2 ofQ �7 <br />