Laserfiche WebLink
• RXK Series Scissor Lift Racks <br /> 11.1.1.Air Supply for Jacks 32 <br /> 11.1.2.Air Lines of Inflation Station(optional equipment) 32 <br /> 11.1.3.Air Lines of PowerSlide(optional equipment) 33 <br /> 11.2. Install Air Filter and Connect Customer Air Supply to Console 33 <br /> 11.3. Burndy Cable to Aligner(Only for Wired FIA) 33 <br /> 11.4. Connect Sensor Cables 34 <br /> 11.4.1. For Surface Mount RX lifts&all International Surface Mount RX Lifts-Connect Sensors to Board 34 <br /> 11.5. Rack Lighting 35 <br /> 12. Console Wiring Diagram 36 <br /> 13.Anchor Bases&Console 39 <br /> 13.1. Leveling Runways 39 <br /> 13.2. Install Anchor 40 <br /> 13.3. Floor leveling kit 20-3063-1 or kit 20-3524-1 (BMW&Mercedes-Benz Only) 41 <br /> 13.3.1.Assembly 41 <br /> 13.3.2. Installation 41 <br /> 13.4. Final Leveling 42 <br /> 13.5. Grout under Base Frames 43 <br /> 13.6. Secure the Control Console to Floor 44 <br /> 13.6.1. Drill Holes&Anchors 44 <br /> 14. Completing Install 47 <br /> 14.1.Adjusting the Locking Mechanism 47 <br /> 14.2. Installation MKS Bracket 48 <br /> 14.3. Install Filler Plates 48 <br /> 14.4.Approach Ramps(surface installation only) 49 <br /> 14.5. Down Bolts-(RX14KL Surface Mount&RXI6KLF Pit Rack Only) 50 <br /> 14.6.Wheel Stops and Etc. (surface installation only) 50 <br /> 14.7. Exit Ramps,Approach Ramps, and Etc. (flush-mount lifts only) 51 <br /> 14.8. Inflation Station(optional feature) 52 <br /> 14.9. Calibration of the Auto-Leveling System 53 <br /> 14.10.Turnplate Installation(RX10 and RX12) 54 <br /> 14.10.1.Air Supply for PowerSlide Turnplates 55 <br /> 14.10.2.Guide Strip for Manual Turnplates,20-2531-1,20-2532-1 or 20-2533-1 55 <br /> 14.11.Turnplate Installation(RX14 and RX16) 55 <br /> 14.12. Check Operation of Inflation Station(optional feature) 56 <br /> 14.13. Check Operation of PowerSlide(optional feature) 57 <br /> 14.14.Wireless FIA-WinAlign&Rack Console Set Up 57 <br /> 14.15. Grease Rub Blocks&Tracks 58 <br /> 14.16. Run in Procedure 59 <br /> 14.17. Completion 60 <br /> 15. Install PowerSlide Mechanism 61 <br /> 15.1. Route PowerSlide Air Lines 63 <br /> 15.2. Inflation Station Installation and Air Lines 63 <br /> 15.3. Modify Console for Added Options 64 <br /> 15.4. Prepare for operation with new features 65 <br /> 15.5. Intrinsically Safe Barrier Kit 20-3148-1 65 <br /> 16. Rack Lighting 66 <br /> 16.1. Rack Lighting(Front) 66 <br /> 16.2. Rack Lighting(Rear) 66 <br /> 16.3. Power Supply 69 <br /> 16.4. Power Connections 69 <br /> 16.5. Change Rack Lighting Height 70 <br /> 16.5.1.Troubleshooting 70 <br /> 16.6. Lighting Cables 70 <br /> 17.Threshold Covers 72 <br /> 18. Position Control System(MKS)-Mercedes Benz Only 73 <br /> 18.1. Equipment Preparation for MKS Test-Conventional Sensors 73 <br /> 18.1.1. DSP508 and HS401 Series Sensors 74 <br /> 18.2. Setting MKS Measurements to Zero 74 <br /> 18.2.1.Checking the Level of the Lift 75 <br /> 18.2.2.Checking Conventional Wheel Alignment Sensors 75 <br /> 18.3. Rotation Limiter-Approach Ramp Extensions 75 <br /> 18.3.1. Preparation for Initial Installation 76 <br /> Page 3 ofQ to <br />