Laserfiche WebLink
Page 3 of 8 <br /> ® QUICK RESPONSE <br /> DRY HORIZONTAL <br /> N41KJNG* SIDEWALL SPRINKLERS <br /> The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 <br /> Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com <br /> Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com <br /> )K*Notei A 1/2" ratchet is required, <br /> Sprinkler Wrench Part (Not available from Viking) <br /> No 07565W/B)K)K for <br /> installing recessed <br /> dry sprinklers. <br /> _, <br /> If I I f I---------- <br /> it <br /> Step 1: Carefully slide the Step 2: Press the wrench onto <br /> wrench sideways around the the sprinkler wrench flats and <br /> deflector and protective turn slightly to ensure engage- <br /> shield as shown ment with the wrench flats. <br /> Figure 2: Wrench 07565W/B for Adjustable Recessed Dry Horizontal Sidewall Sprinklers <br /> For 'A' Dimension: <br /> 1. Determine the distance from the face of Deflector at NOTE1 <br /> the tee to the finished face of the wall \ Minimum Distance To locate the deflector <br /> 2. Round to the nearest 1/2' (12.7 mm) between L Finished Ceiling rrom wall at the minimum distance <br /> 1-1/2' (38.1 mm) and 45-1/2' (1,156 mm). from the wall, with no <br /> adjustment available, <br /> NOTE: The deflector will extend approximately Finished Wall order the standard dry <br /> 4-1/8' (104.8 mm) from the wall with 2' +/- 4' (102 mm) Minimum horizontal sidewall sprink- <br /> 1' (25.4 mm) in <br /> adjustment available. 6' (152 mm) Maximum)K ter 1' (25.4 mm) shorter <br /> A 3-1/8' than the 'A' Dimension. <br /> i-. (79.4 mm) <br /> --- Deflector at NOTE <br /> 3-1/16' Maximum Distance To locate the deflector <br /> 177,8 mm) From wall at the maximum distance <br /> from the wall, with no <br /> Q*L:/7Z adjustment available, <br /> Y17'J_ <br /> order the standard dry <br /> (15.9� -- horizontal sidewall sprink- <br /> ler <br /> 5 <br /> Minimum wall opening 5-1/8' than the 4A Dimension. <br /> diameter: 1-3/4' (44.5 mm). Sleeve diameter) (130,2 mm) <br /> Maximum wall opening 1-1/2' (38.1 mm). <br /> diameter) 2-1/4' (57 mm), 13/16' Sleeve finish matches x May be allowed up to 18' (457 mm) for certain <br /> (20.6 mm) finish of escutcheon. FM installations. Refer to the appropriate installation <br /> standards, including NFPA 13 and/or FM Loss <br /> Prevention Data Sheet 2-0. <br /> Figure 3: Adjustable Standard Dry Horizontal Sidewall Sprinkler <br /> 41 <br /> Slot <br /> -Deflector Slot <br /> Push and Rotate <br /> Sleeve <br /> STEP 1: Align the slot in STEP 2: Push the rounded STEP 3: Pull the escutcheon STEP 4: Push and rotate STEP 5: To minimize <br /> the escutcheon with the end of the slot against the away from the near edge the escutcheon onto the visibility of the slot <br /> her, <br /> surface of near edge of the deflector. of the deflector. Move the sleeve, in the escutcheon, <br /> the deflector as shown. Push the far side of the near side of the escut- position the slot <br /> escutcheon past the deflec- cheon over the deflector, at the top of the <br /> tor, toward the sleeve, sprinkler sleeve. <br /> Figure 4: Adjustable Standard Escutcheon Installation <br /> Form No. F_031993 20.04.16 Rev 20.1 <br />