3003 W CASINO RD BASE FILE 2025-01-31

Page 8 of 8 ® QUICK RESPONSE DRY HORIZONTAL N41KJNG* SIDEWALL SPRINKLERS The Viking Corporation, 210 N Industrial Park Drive, Hastings MI 49058 Telephone: 269-945-9501 Technical Services: 877-384-5464 Fax: 269-818-1680 Email: techsvcs@vikingcorp.com Visit the Viking website for the latest edition of this technical data page: www.vikinggroupinc.com 5-1/8" a (130.2 mm)— Seal the clearance space around the sprinkler barrel to avoid ii ii ii Maximum Leakage of air Into the protected area and consequent formation of condensate around the sprinkler frame, which could inhibit -- operation or cause premature operation. Refer to Figure 9. If humidity and temperature " " " NOTE: To locate the differential causes condensation ------------------- Deflector at deflector at the on the exposed dry sprinkler IIIIIIIII__________________= Maximum Distance maximum distance from barrel, consider wrapping the IIIIIIIII=====_____________- From Wait the wall, with no exposed barrel with insulation, P IIIIIIIII 13/16" adjustment available,20.6 mm) foam Insulating tape, or equivalent IIIIIIIII Ceiling order the standard IIIIIIIII dry horizontal side- Install the 1" NPT threaded 4' (102 mm) Minimum wall sprinkler 1" end of the dry sldewal( sprink- ii ii ii 6' (152 mm) Maximum)K longer than the "A" ler into the 1" NPT outlet of I��I��II�� Sleeve finish dimension. a malleable iron tee fitting per matches ANSI B 16,3 (Class 150) or cast escutcheon Iron threaded tee fitting per 3-1/16" Up to 2' (50.8 mm) ANSI 16,4 (Class 125) only, adjustment is available, (77.8 mm) 5/8" Minimum wall opening (15.9 mm) 3-1/8' diameter: 1-3/4' (445 mm� „ (79.4 mm) (Exposed Maximum wall opening Minimum Barrel) 1-1/2' �� diameters 2-1/4' (57 mm). (381 mm) n i� 'i'i NOTE: To locate the diameter deflector at the minimum distance from xpose arre Outer the wall, with no Ambient Ambient Temperature Temperature Surface adjustment available, of Protected 40°F/4°C 50°F/l0°C 60°F/16°C of the Wall _ order the standard Area## at the Exposed Minimum Barrel dry horizontal side- Discharge End Length— Face of the ii ii 'i'i wall sprinkler 1" of the Sprinkle Tee to the Outer ii ii ii Deflector at shorter than the Surface of the Wall Minimum Distance "A" dimension. In.(mm) In.(mm) In.(mm) From Wall 40°F WC) 1 0 0 1 0 30°F (-1°C) 0 0 0 11May be allowed up to 18' (457 mm) for certain FM 20°F (-7°C) 4 (100) 0 0 installations. Refer to the appropriate installation standards, 10°F (-12°C) 8 (203) 1 (25.4) 0 including NFPA 13 and/or FM Loss Prevention Data Sheet 2-0. 0°F (-18°C) 12 (305) 3 (76) 0 x#The protected area refers to the area below the ceiling, -10°F (-23°C)14 (356) 4 (102) 1 (25.4) The ambient temperature is the temperature at the discharge end of the sprinkler, -20°F (-29'C)14 (356) 6 (152) 3 (76) For protected area temperatures that occur between the -30°F (-34"C)16 (406)8 (203)4 (102) values listed, use the next cooler temperature. -40°F (-40°C)18 (457)8 (203)4 (102) )-)-The minimum required barrel length is not the same as the "A" dimension. -50°F (-46°C)20 (508)10 (254)6 (152) Refer to Figures 3, 5, 6 and 7 for the "A" dimension. -00°F (-51°C)20 (508)10 (254)6 (152) Exposed minimum barrel lengths are inclusive up to 30 mph wind velocities, Figure 8: Dry Horizontal Sidwall Sprinkler Required Minimum Barrel Length Based on Ambient Temperature in the Protected Area (Adjustable Standard Dry HSW Sprinkler is Shown) Seal 22087M/W Seal (or equivalent method) Clearance Opening Insulated Insulated Wall Wall Dry Sprinkler Seal on the Exterior of the Wall Dry Sprinkler Seal Within the Wall Figure 9: Dry Sprinkler Seal (Adjustable Standard Dry HSW Sprinkler is Shown) Replaces Form No. F_031993 Rev 19.2 Form No. F_031993 20.04.16 Rev 20.1 (Removed cover 15610.)