9700 HOLLY DR 2025-07-10 - Laserfiche WebLink

LATITUDEProduct Guide:Latitude"Series Metal Wall Panels B. Uniform Wind Load Capacity. 1. Manufacturers not listed above must submit for approval, 1. Installed wall panel system shall withstand positive and ten(10)days prior to bid date,the following:Manufacturer's negative wind pressures complying with the following literature; certification of testing in accordance with criteria. specification requirements and sections 1.2 and 1.6;sample a. Design Code:ASCE 7,Method 2 for Components and warranties in accordance with specification section 1.7; Cladding. installer qualifications in accordance with specification b. Safety Factor:The panel system shall withstand a"proof section 1.5,and a list of five(5)similar projects in size and load"equal to 150%of the design wind pressure,as scope of work. per the ASTM E330 testing standard. 2. No substitutions will be permitted after the bid date of this c. Category**Select**<I,II,Ill,or IV>Building with an project. Importance Factor of**Select**<0.77,1.00,or 1.15>. C. Materials. d. Wind Speed: mph. 1. Panel materials:**Select Material**[24 or 22 or 20]gauge e. Exposure Category:**Select**<B,C,or D>. G90 galvanized steel,per ASTM A653 or AZ50 Galvalume f. Maximum Wall Height: feet. steel,per ASTM A792 g. Minimum Building Width: feet. or[0.032"or 0.040"or 0.050"or 0.063"]aluminum,3105-H14 h. Roof Pitch: inches per foot. aluminum alloy,per ASTM B209 Design Wind Pressure: or[0.7 mm or 0.8 mm or 1.0 mm]rolled zinc,Type 710,per Zone 4-Field of Wall:+ psf and - psf ASTM B69. Zone 5-Building Corners: + psf and - psf 2. Flashing and flat stock material: Fabricate in profiles 2. Capacity shall be determined using defined method in indicated on drawings of same material,thickness,and accordance with ASTM E330. finish as wall panel system,unless indicated otherwise. C. Air infiltration:The panel system shall be tested in accordance **If Specifying Mill Finish Panels,Delete the Following with ASTM E283,and meet or exceed the following performance Section requirements: D. Finish on exposed surfaces. Pressure Area Leakage Rate 1. Two coat coil applied,baked-on full-strength(70%resin) 1.57 PSF >0.06 cfm/sq.ft. fluorocarbon coating system(polyvinylidene fluoride,PVF2), applied by manufacturer's approved applicator. D. Static air pressure water infiltration:The panel system shall be 2. Coating system shall provide nominal 1.0 mil dry film tested in accordance with ASTM E331,and meet or exceed the thickness,consisting of primer and color coat. following performance requirements: **Select Appropriate Color Option Below** Pressure Result a. Color shall be Imetco's 5 Gal/Hr per S.F.and Static Air No Leakage b. Color shall be selected from Imetco's Standard Colors. Pressure of 12.0 psf for 15 minutes c. Color:Custom color selected by architect. E. Missile Impact Test and Cyclic Wind Pressure Test:The panel d. Color shall be: system shall be tested in accordance with ASTM El 886 and E1996 e. Zinc panels shall be furnished United Zinc pre- <or FBC Test Protocols TAS 201 and TAS 203>. weathered"Glacier Gray". 3. Unexposed surfaces of painted steel or aluminum materials 1.7 WARRANTIES. shall be baked-on polyester coating with.20-.30 mil total A. Endorse and forward to owner the following warranties: dry film thickness(TDF). 1. 10 year limited waterrtight warranty,jointly signed by the 4. Unexposed surface of Zinc panels shall be 5 mil minimum installer and the manufacturer. plastisol high performance coating system. 2. Manufacturer's standard 20 year finish warranty covering lf Specifying Painted Panels,Delete the Following Section * checking,crazing,peeling,chalking,fading,and adhesion. (note:G90 galvanized material is only provided as a painted product) 3. Installer's 2 year warranty covering wall panel system installation and watertightness. E. Finish on exposed and unexposed surfaces shall be bare,as delivered from the mill. B. Warranties shall commence on date of substantial completion. F. Characteristics. 2.0 PRODUCTS. 1. Fabrication: Panels shall be factory formed from specified 2.1 METAL WALL PANEL SYSTEM. metal. 2. Profiles shall be as indicated project drawings. A. Panel shall be Imetco LATITUDE Wall system as manufactured a. The standard profile shall provide ribs at4"on center. by Innovative Metals Company,Inc.(Imetco),Tucker,Georgia, b. Alternate profile panels shall be used to provide reveals telephone 1-800-646-3826. of single 8,double 8';or 12"accent bands as shown on B. Alternate manufacturers are subject to full compliance with project drawings. specification requirements,and shall be submitted for approval c. Web elements of the ribs shall be[asymmetrical or as follows: symmetrical]angle. 3. Panel orientation: [Horizontal or Vertical]. www.imetco.com I (800)646-3826 Page 20 /M E 7 CO