Laserfiche WebLink
1. ASTM D 412 - Standard Test Methods for Vulcanized Rubber and Thermoplastic <br /> Elastomers-Tension. <br /> 2. ASTM C 1289 - Standard Specification for Faced Rigid Cellular Polyisocyanu rate Thermal <br /> Insulation Board <br /> 3. ASTM D 6878 - Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing. <br /> 4. ASTM D1621 - Compressive Properties of Rigid Cellular Plastics <br /> 5. ASTM D1622 -Apparent Density of Rigid Cellular Plastics <br /> 6. ASTM D2126- Response of Rigid Cellular Plastics to Thermal and Humid Aging <br /> 7. ASTM D3273- 16 Standard Test Method for Resistance to Growth of Mold on the Surface <br /> of Interior Coatings in an Environmental Chamber <br /> 8. ASTM E84 - Surface Burning Characteristics of Building Materials <br /> 9. ASTM E96/E96M -Water Vapor Transmission of Materials <br /> H. Underwriter's Laboratories: <br /> 1. UL Class A or B <br /> 2. UL 1256 - Fire Test of Roof Deck Constructions <br /> 1.05 PERFORMANCE REQUIREMENTS: <br /> A. General: Provide installed roofing membrane, insulation boards, base flashing system and <br /> other related flashings and accessories that will remain watertight, will not permit the passage <br /> of water, and resist specified uplift pressures, thermally induced movement, and exposure to <br /> weather, without failure. Install products for a complete roofing system that can be warranted by <br /> the manufacturer for a period of twenty years. <br /> B. Material Compatibility: Provide roofing materials that are compatible with one another under <br /> conditions of service and application required, as demonstrated by roofing membrane <br /> manufacturer, based on testing and field experience. <br /> C. Wind Resistance: <br /> 1. Refer to Design Criteria in the project drawing set. <br /> 2. In cases where the roof/deck assembly lacks testing data, contractor shall perform a <br /> minimum of 10 pull tests (to failure)with the roof membrane and insulation fasteners to <br /> determine the minimum, maximum and average pull-out resistance. Outliers shall be <br /> omitted, and the average value shall be used to determine the minimum fastener <br /> frequency for attaching the roof system. Contractor shall submit data to the roofing <br /> manufacturer named in the bid for verification of the fastener frequency and patterns <br /> required to meet the minimum requirements outlined in the construction documents. <br /> 3. After determining the design wind uplift pressures (including the safety factor) on the roof <br /> and fastener pull out resistance, contractor shall secure the roof insulation, membrane, <br /> and edge flashing products to comply with the design, performance and installation <br /> requirements as demonstrated by the manufacturer's independent testing and in <br /> accordance with one of the following recognized authorities: <br /> a. Factory Mutual Global (FMG) Loss Prevention Data Sheets: <br /> 1) Bulletin 1-29, latest edition, Roof Deck Securement and Above Deck Roof <br /> Components <br /> 2) Bulletin 1-49, latest edition, for Wind Uplift Pressures on Roof Edges. <br /> b. ANSI/SPRI: <br /> 1) Bulletin WD-1, "Wind Design Standard Practice for Roofing Assemblies" <br /> 2) Bulletin FM 4435/ES-1, "Wind Design Standards for Edge Systems Used with <br /> Low Slope Roofing Systems" <br /> D. External fire Resistance: System components shall have been tested in accordance with ASTM <br /> E 108, with a Class A rating for application and roof slopes indicated, as determined by testing <br /> identical membrane roofing materials by a qualified testing agency. Materials shall be identified <br /> with appropriate markings of applicable testing agency. The roof system assembly shall also <br /> meet or exceed an Underwriter's Laboratories' (UL) Class A rating as tested in accordance with <br /> test method UL- 790. <br /> SEA00511 / Prologis - SEA00511 07 5400 - 2 THERMOPLASTIC MEMBRANE <br /> - FY24- Everett 1 - Capital ROOF SYSTEM <br /> Roofing Project <br />