Laserfiche WebLink
3 I B9512G Control Panels <br /> Communication formats Bosch Remote Connect(Cloud) <br /> The control panel prioritizes and sends reports to four Remote Connect simplifies connections from RPS,and <br /> route groups. Network and phone communications can the Remote Security Control app, using Bosch Cloud <br /> use one of two communicationformats: <br /> form s. Modem4, services.This service creates a secure connection to <br /> Contact ID. Each group has a programmable primary the control panel without specific router settings or <br /> and backup destination. the need for a static IP address or DNS. <br /> The control panel provides flexible communications for <br /> most central stations with reporting capabilities such • Notice <br /> as: 1 <br /> The Bosch Remote Connect service is not <br /> • Individual point numbers available in Europe,the Middle East,or Africa. <br /> • Opening or closing reports by user and area number <br /> • Remote programming attempts <br /> • Diagnostic reports Firmware updates <br /> The system allows remote firmware updates: <br /> • Control panel updates. Remotely update the control <br /> 1 Notice panel firmware for easy feature enhancements <br /> — For premises equipment used in the without replacing ROM chips. <br /> communication path,such as routers, use only UL • Module update support. Remotely update the <br /> listed equipment. firmware on connected SDI2 modules for easy feature <br /> enhancements without visiting each individual <br /> IP communication module. <br /> The control panel can use IP to communicate with a Firmware updates occur through Remote Programming <br /> Conettix D6600 or a Conettix D6100IPv6 Software (RPS) and the RPS Firmware Update Wizard. <br /> Communications Receiver/Gateway. Use one of the The Firmware Update Wizard uses the on-board USB <br /> following for IP: connection or the on-board Ethernet (IP) connection <br /> • The on-board Ethernet connection (the on-board (the on-board Ethernet port is excluded on "E" <br /> Ethernet port is excluded on"E"versions). versions) to transfer firmware updates. <br /> • A B426. The control panel can optionally receive firmware <br /> • A plug-in cellular communicator(B440/B440-C/B441/ updates from RPS. Use one of the following <br /> B441-C/B442/B443/B444). communication methods: <br /> Conettix IP communication provides a secure path that • B426 <br /> includes anti-replay/anti-substitution features, and • Plug-in cellular communicator: B440/B440-C/B441/ <br /> enhanced security with up to AES 256-bit encryption B441-C/B442/B443/B444 <br /> (using Cipher Block Chaining (CBC)). <br /> The control panel supports Domain Name System •• Notice <br /> (DNS) for both remote programming and central Data rate apply <br /> station communication. DNS provides ease of use, Cellular firmware updates require more time than <br /> eliminating the need to use static IP addresses as your Ethernet updates and carrier data rates apply. <br /> reporting destination,and accommodates a simple <br /> solution for central station disaster recovery.The A wide variety of input options <br /> control panel supports both IPv6 and IPv4 networks. Each point: <br /> Communication paths • Single 1 ko, single 2 ko,dual 1 kG(1 kG+1 kG),and <br /> The control panel accommodates up to four separate No EOL (end-of-line) (EOL) resistor options (for on <br /> phone and four separate network paths to the central board and B208 inputs) <br /> • <br /> station receiver.When resetting alarms or turning a Programmable for Fire, Intrusion,Access,Gas,and <br /> system on and off, the user is identified by name and Supervisory devices <br /> • Supports hardwired and wireless devices <br /> number. • Supports IP cameras by Bosch as point and output <br /> Personal notification devices <br /> The control panel can send text messages and emails IP camera support <br /> for personal notification over Ethernet or using a The control panel can integrate directly with Bosch IP <br /> cellular communicator.You can configure up to 32 cameras, using them as fully supervised points and <br /> destinations using a combination of cellular phone outputs. <br /> numbers and email addresses.The control panel sends <br /> Integration of cameras allows the camera's video <br /> notifications in the user's programmed primary motion detection to activate points on the control <br /> language. <br /> panel.The control panel's virtual outputs can be <br /> configured to trigger camera actions, including <br /> sending video snapshots via email. <br />