7100 HARDESON RD 2021 Plans 2025-03-19

Applications Standards and Codes Example 1: Expand notification appliance power an additional 6.0 A The FCPS-24S6 and FCPS-24S8 comply with the following stan- (FCPS-24S6)or 8.0 A(FCPS-24S8). Use up to four Class B (Style dards: Y) outputs or four Class A (Style Z) outputs (using ZNAC-4). For NFPA 72 National Fire Alarm Code example, the FACP notification appliance circuits will activate the FCPS when reverse-polarity activation occurs. Trouble conditions • UL 864 Standard for Control Units for Fire Alarm Systems (NAC on the FCPS are sensed by the FACP through the notification appli- expander mode) ance circuit. • UL 1481 Power Supplies for Fire Alarm Systems Example 2: Use the FCPS to expand auxiliary regulated 24-volt system power up to 4.0 A(FCPS-24S6)or up to 6.0 A(FCPS-24S8). Agency Listings and Approvals Both resettable and non-resettable power options are available. These listings and approvals apply to the modules specified in this Resettable outputs are created by connecting the resettable output document. In some cases, certain modules or applications may not from the FACP to one or both of the FCPS inputs. be listed by certain approval agencies,or listing may be in process. Example 3: Use addressable control modules to activate the FCPS Consult factory for latest listing status. instead of activating it through the FACP notification appliance cir- • UL Listed:S635,S674 cults. This typically allows for mounting the FCPS at greater dis- ULC Listed:S635(FCPS-24S6C&FCPS 24S8C) tances*away from the FACP while expanding system architecture in various applications. • CSFM Approved:7315-0028:0225 For example,an addressable control module is used to activate the • MEA:299-02-E FCPS, and an addressable monitor module is used to sense FCPS • FM Approved trouble conditions. Local auxiliary power output from the FCPS pro- vides power to the addressable control module. Ordering Information NOTE:Addressable FACPs are capable of locating control and monitor FCPS-24S6: 6.0 A, 120 VAC remote charger power supply. modules at distances of up to 12,500 feet(3,810 meters). Includes main printed circuit board,transformers,enclosure(15"H x 14.5"W x 2.75"D [cm: 38.1H x 36.83W x 6.985D]), and installation Sync Follower/Generator Note instructions In some installations, it is necessary to synchronize the flash timing FCPS-24S6C: Same as above,ULC-listed of all strobes in the system for ADA compliance.Strobes accomplish FCPS-24S6R: Same as FCPS-24S6 with red enclosure this by monitoring very short timing pulses on the NAC power which are created by the FACP.When installed at the end of a NAC wire FCPS-24S6E: 6.0 A, 240 VAC remote charger power supply. run, the FCPS-24S6/-2458 can track (i.e. "follow") the strobe syn- Includes main printed circuit board,transformers,enclosure (15"H x chronization timing pulses on the existing NAC wire run.This main- 14.5"W x 2.75"D [cm: 38.1H x 36.83W x 6.985D]), and installation tains the overall system flash timing of the additional strobes instructions attaches to the FCPS. FCPS-24S8: 8.0 A, 120 VAC remote charger power supply. When the FCPS-24S6/-2458 is configured (via DIP switch settings) Includes main printed circuit board,transformers,enclosure(15"H x as a "sync follower," the FCPS' NAC outputs track the strobe syn- 14.5"W x 2.75"D [cm: 38.1H x 36.83W x 6.985D]), and installation chronization pulses present at the FCPS' sync input terminal. The instructions pulses originate from an upstream FACP or other power supply. FCPS-24S8C: Same as above,ULC-listed When the FCPS-24S6/-24S8 are configured (via DIP switch set- FCPS-24S8R: Same as FCPS-24S8 with red enclosure tings)as a"sync generator,"the FCPS'sync input terminals are not used. Rather,the FCPS is the originator of the strobe synchronize- FCPS-24S8E: 8.0 A, 240 VAC remote charger power supply. tion pulses on the FCPS' NAC outputs. In "sync generator" mode, Includes main printed circuit board,transformers,enclosure(15"H x the sync type (System Sensor, Wheelock, or Gentex) is selectable 14.5"W x 2.75"D [cm: 38.1H x 36.83W x 6.985D]), and installation via DIP switch settings. instructions ZNAC-4: Class A(Style Y)NAC option module EOLR-1: 12/24 VDC end-of-line relay for monitoring four-wire smoke detector power BAT-1270: Battery, 12-volt, 7.0 AH (two required, see BAT Series data sheet DN-6933) PS-1270: Battery, 12-volt,7.0 AH(two required) ISO 9001 • MIMES IMLUL1KIIwI QUALITY SYSTEMS This document is not intended to be used for installation purposes. We try to keep our product information up-to-date and accurate. We cannot cover all specific applications or anticipate all requirements. All specifications are subject to change without notice. NOTI PIER NOTIFIERSand System Sensor®are registered trademarks of Honeywell International Inc.Wheelock©is a registered trademark of Cooper Technol- �w 12 Clintonville Road ogies Company.Gentex®is a registered trademark of Centex Corpora- Northford,CT 06472 fen. ` N OT 1 F 1 E R ©2019 by Honeywell International Inc.All rights reserved.Unauthorized 203.484.7161 use of this document is strictly prohibited. by Honeywell www.notifier.com Country of Origin:USA