3700 FEDERAL AVE PORTABLE 6 JACKSON ELEMENTARY 2025-08-07

Application Dimensions The BPS provides additional power and circuits for notification ap- pliances and other 24 Vdc loads. It is listed for indoor dry locations O Q and can easily be installed where needed. Q Top View Fault conditions are indicated on the on-board diagnostic LEDs, opening the BPS input sense circuit and the trouble relay(if D2 D3 programmed).While this provides indication to the host system, the BPS can still be activated upon command.A separate AC Fail contact is available on the BPS circuit board,which can be 84 D4 o0 programmed for trouble or AC Fail.There are seven on-board ° diagnostic LEDs: one for each NAC fault, one for battery fault, one Front View.22 O for ground fault, and one for AC power. > The unique dual-input activation circuits of the BPS can be acti- vated by any voltage from 6 to 45 VDC(filtered-regulated)or 11 D1 fn O D6 to 33 Vdc(full-wave rectified, unfiltered).The first input circuit can O ° be configured to activate 1-4 of the four possible outputs.The C/) second input circuit can be configured to control circuits 3 and 4. All knockouts When outputs are configured for auxiliary operation,these circuits for 3/4 in conduit G `D can be configured to stay on or automatically deactivate 30 sec- ° (1.9 cm) onds after AC power is lost.This feature makes these circuits ideal IF for door holder applications.The BPS also has a separate 200 mA 24 Vdc output that can be used to power internal activation modules. BPS NACs can be configured for a 3-3-3 temporal or continuous Di D2 D3 D4 D5 D6 output.This makes the BPS ideal for applications requiring signal- 17.0 in 3.5 in 13.0 in 6.5 in 3.375 in 12.0 in ing rates that are not available from the main system. (43.2 cm) (8.9 cm) (33.0 cm) (16.5 cm) (8.6 cm) (30.4 cm) In addition to the internally generated signal rates,the BPS can also be configured to follow the coded signal rate of the main system NACs.This allows for the seamless expansion of existing Wire routing Power-limited NACs. wiring area The BPS enclosure has mounting brackets for up to three Signa- ture modules to the right of the circuit board. 0° Engineering Specification Supply,where needed, EDWARDS BPS Series Booster Power [2] Supplies(BPS)that are interconnected to and supervised by the ❑ °o main system.The BPS shall function as a stand-alone auxiliary ❑ power supply with its own fully-supervised battery compliment. The BPS battery compliment shall be sized to match the require- ments of the main system.The BPS shall be capable of supervis- Route AC supply o° 9 ing and charging batteries having the capacity of 24 ampere-hours through these for Mass Notification/Emergency Communication(MNEC), life knockouts only safety applications. (Nonpower-limited and supervised) Battery wiring (nonpower- <<The BPS shall be capable of installation for a seismic com- o limited and supervised) o ponent Importance Factor of 1.5.>>The BPS shall provide a minimum of four independent,fully supervised Class B circuits Battery Battery that can be field configurable for notification appliance circuits or auxiliary 24 Vdc power circuits. BPS NACs shall be convertible to a minimum of two Class A NACs. Each BPS output circuit shall be rated at 3 amperes at 24 Vdc. Each output circuit shall be pro- vided with automatically restoring overcurrent protection.The BPS Notes shall be operable from the main system NAC and/or EDWARDS 1. Maintain 1/4-inch(6 mm)spacing between power-limited and nonpower-limited Signature Series control modules. BPS NACs shall be configurable wiring or use type FPL,FPLR,or FPLP cable per NEC. [2] Power-limited and supervised when not configured as auxiliary power.Non- for continuous or 3-3-3 temporal rate. Fault conditions on the BPS supervised when configured as auxiliary power. shall not impede operation of main system NAC.The BPS shall be [3] Source must be power-limited.Source determines supervision. provided with ground fault detection circuitry and a separate AC 4. When using larger batteries,make sure to position the battery terminals towards fail relay. the door. Page 2 of 4 DATA SHEET E85005-0125 Not to be used for installation purposes. Issue 1.2