8102 EVERGREEN WAY 2020 EVERETT 4 CORNERS - BLDG A Plans 2025-06-20

GENERAL NOTES F.MATERIALS ACCESSIBILITY NOTES m 1.THERMAL AND SOUND INSULATING MATERIALS(IBC SECTION 7201: REQUIRED FLAME SPREAD INDEX OR SMOKE- A,GENERAL D.ACCESSIBLE ROUTE OF TRAVEL CONTINUED DEVELOPED INDEX SHALL BE DETERMINED IN ACCORDANCE WITH ASTM E 84 OR UL 723. (CONTINUED) A.GENERAL A. INSULATION MATERIALS IN A CONCEALED INSTALLATION SHALL HAVE A FLAME SPREAD INDEX OF NOT MORE THAN JOHNSON BRAU N DINS. 1.BUILDINGS AND FACILITIES SHALL BE DESIGNED AND CONSTRUCTED TO BE ACCESSIBLE B. DOORS AND DOORWAYS(ICC At 17.1-2009 SECTION 404): 25 AND A SMOKE-DEVELOPED INDEX OF NOT MORE THAN 450.(IBC SECTION 720.2) 15200 52nd Ave.South 1.NOTIFY THE ARCHITECT OF ANY DISCREPANCIES THAT EXIST WITHIN THE DRAWINGS B. INSULATION MATERIALS IN AN EXPOSED INSTALLATION SHALL HAVE A FLAME SPREAD INDEX OF NOT MORE THAN 25 IN ACCORDANCE WITH THE IBC CHAPTER 11:ACCESSIBILITY AND ICC/ANSI At 17.1-2009,AS Suite 300 AND ASMOKE-DEVELOPED INDEX OF NOT MORE THAN 450.(IBC SECTION 720.3) AMENDED AND THE 2010 AMERICANS WITH DISABILITIES(ADA)STANDARDS FOR ACCESSIBLE 1. CLEAR WIDTH:DOORWAYS SHALL HAVE A CLEAR OPENING WIDTH OF 32"MINIMUM, Seattle,WA 98188 2.ALL METHODS,MATERIALS AND WORKMANSHIP SHALL CONFORM TO THE GOVERNING CODES LISTED PER SHEETS BELOW: C. CELLULOSE LOOSE-FILL INSULATION SHALL COMPLY WITH CPSC 16 CFR,PART 1209 AND PART 1404(IBC SECTION DESIGN.THE 1998 FAIR HOUSING ACT DESIGN MANUAL(FHADM)HAS BEEN USED ON THE MEASURED BETWEEN THE FACE OF THE DOOR AND THE STOP,WITH DOOR OPENED phone 206.766.8300 BUILDING A:CS01A,CS02A,CS03A 720 6) DESIGN OF THIS BUILDING AND SERVES AS SAFE HARBOR FOR COMPLIANCE WITH THE HUD 90 DEGREES.OPENINGS WITHOUT DOORS MORE THAN 24"IN DEPTH SHALL -phnsonhraund- BUILDING B:CS01B,CS02B,CS03B D. INSULATION COVERING ON PIPE AND TUBING SHALL HAVE A FLAME SPREAD INDEX OF NOT MORE THAN 25 AND A FEDERAL FAIR HOUSING ACT. PROVIDE A CLEAR WIDTH OF 36".THERE SHALL BE NO PROJECTIONS LOWER THAN BUILDING C:CS01 C,CS02C,CS03C SMOKE-DEVELOPED INDEX OF NOT MORE THAN 450.(IBC SECTION 720.7) 34".PROJECTIONS BETWEEN 34"AND 80"SHALL NOT EXCEED 4".(EXCEPTION DOOR ARCHITECTURE BUILDING D:CS01D,CS02D,C803D 2.&COPING:SITES,BUILDINGS,STRUCTURES,FACILITIES,ELEMENTS AND SPACES, CLOSERS AND STOPS ARE PERMITTED TO BE 78"ABOVE THE FLOOR.) INTERIOR DESIGN BUILDING E:CS01E,CS02E,CS03E TEMPORARY OR PERMANENT,SHALL BE ACCESSIBLE TO PERSONS WITH PHYSICAL 2. MANEUVERING CLEARANCES AT DOORS:PER ICC At 17.1-2009 TABLE 404.2.3.2 AND Greg L.Alims, 2.FOAM PLASTIC INSULATION SHALL CONFORM TO THE REQUIREMENTS OF IBC SECTION 2603:UNLESS OTHERWISE DISABILITIES.(IBC SECTION 1103.1) FIGURE 404.2.3.2. Jeffrey A.Williams, 3.COMPLY WITH ALL APPLICABLE CODES&ORDINANCES. INDICATED IN THIS SECTION,FOAM PLASTIC CORES OF MANUFACTURED ASSEMBLIES SHALL HAVE A FLAME SPREAD INDEX 3. THRESHOLDS:MAX.1/2"IN HEIGHT,BEVELED NO STEEPER THAN 1:2. OF NOT MORE THAN 75 AND A SMOKE DEVELOPMENT INDEX OF NOT MORE THAN 450 TESTED IN ACCORDANCE WITH ASTM 3.PARKING(IBC SECTION 1106):REFER TO SHEET A020 FOR ACCESSIBLE PARKING 4. TWO DOORS IN SERIES:48"MIN+DOOR WIDTH OPENING INTO SPACE.SPACE 4.UNLESS OTHERWISE NOTED,PLAN DIMENSIONS ARE TO FACE OF STUDS. E 84 OR UL 723. REQUIREMENTS AND STATISTICS. BETWEEN DOORS TO PROVIDE A 60"TURNING SPACE. 5. REFER TO DOOR SCHEDULE NOTES FOR ACCESSIBLE REQUIREMENTS FOR DOOR 5.DO NOT SCALE DRAWINGS 3.WALL AND CEILING FINISHES(IBC SECTION 803):INTERIOR WALL AND CEILING FINISHES SHALL BE CLASSIFIED IN 4.ACCESSIBLE MEANS OF EGRESS(IBC SECTION 1009):ACCESSIBLE SPACES SHALL BE HARDWARE,CLOSING SPEED,DOOR-OPENING FORCE,DOOR SURFACE AND VISION ACCORDANCE WITH ASTM E 84 OR UL 723.THE MAXIMUM FLAME-SPREAD CLASS OF FINISH MATERIALS USED ON INTERIOR PROVIDED WITH NOT LESS THAN ONE ACCESSIBLE MEANS OF EGRESS.WHERE MORE THAN LITES. 6.VERIFY ALL ROUGH-IN DIMENSIONS FOR EQUIPMENT PROVIDED IN THIS CONTRACT OR BY OTHERS. WALLS AND CEILINGS FOR R-2 OCCUPANCIES IN A SPRINKLERED BUILDING SHALL BE CLASS C FOR EXIT ENCLOSURES& ONE MEANS OF EGRESS ARE REQUIRED BY SECTION 1006.2 OR 1009.1 FROM ANY PASSAGEWAYS,CORRIDORS AND ROOMS AND ENCLOSED SPACES.FOR GROUP A-3 IN A SPRINKLERED BUILDING SHALL BE ACCESSIBLE SPACE,EACH ACCESSIBLE PORTION OF THE SPACE SHALL BE SERVED BY NOT C. RAMPS(ICC At 17.1-2009 SECTION 405): 7.REPETITIVE FEATURES ARE OFTEN DRAWN ONLY ONCE AND SHALL BE COMPLETELY PROVIDED AS IF DRAWN IN FULL. CLASS B FOR EXIT ENCLOSURES&PASSAGEWAYS AND CORRIDORS AND CLASS C FOR ROOMS AND ENCLOSED SPACES LESS THAN TWO ACCESSIBLE MEANS OF EGRESS(IBC SECTION 1009.1).EACH REQUIRED 1. SLOPE:MAX.RUNNING SLOPE NOT STEEPER THAN 1:12(8.33%)AND CROSS SLOPE (IBC TABLE 803.11).CLASS B:FLAME SPREAD INDEX 26-75,SMOKE DEVELOPED INDEX 0-450.CLASS C:FLAME SPREAD INDEX ACCESSIBLE MEANS OF EGRESS SHALL BE CONTINUOUS TO A PUBLIC WAY AND SHALL NOT STEEPER THAN 1:48(2%). 8.ALL DOORS NOT LOCATED BY DIMENSIONS ON PLANS,INTERIOR ELEVATIONS,OR DETAILS SHALL BE 3"(2 STUDS)FROM FACE 76-200,SMOKE DEVELOPED INDEX 0-450.(IBC 803.1.1) CONSIST OF ONE OR MORE OF THE FOLLOWING COMPONENTS(IBC SECTION 1009.2): 2. CLEAR WIDTH:36"MIN.CLEAR BETWEEN HANDRAILS. OF ADJACENT STUD WALL TO EDGE OF DOOR ROUGH OPENING. A. ACCESSIBLE ROUTE 3. RISE:30"MAXIMUM. 4.TOILET AND BATHROOM REQUIREMENTS(IBC SECTION 1210) B. HORIZONTAL EXITS 4. LANDINGS:REQUIRED AT TOP AND BOTTOM OF EACH RAMP.MAX.1:48 SLOPE. 9.FINISH FLOOR(FIN.FUR.)REFERS TO TOP OF GYPCRETE OR TOP OF CONCRETE SLAB.SUBFLOOR REFERS TO TOP OF PLYWOOD A. FLOORS AND WALL BASE(IBC SECTION 1210.2.1):IN OTHER THAN DWELLING UNITS,TOILET,BATHING AND C. RAMPS CLEAR WIDTH OF LANDING AT LEAST AS WIDE AS RAMP AND 60"MIN.IN LENGTH. FLOOR SHEATHING. SHOWERS ROOM FLOOR FINISH MATERIALS SHALL HAVE A SMOOTH HARD,NON-ABSORBENT SURFACE.THE WHERE RAMP CHANGES DIRECTION MUST PROVIDE A 60"TURNING SPACE. asss INTERSECTION OF FLOORS AND WALLS SHALL HAVE A SMOOTH,HARD,NON-ABSORBENT VERTICAL BASE THAT 5.SIGNAGE(IBC SECTION 1111):PROVIDE SIGNAGE,DIRECTIONAL SIGNAGE AND OTHER 5. HANDRAILS:RAMPS WITH RISE GREATER THAN 6"ARE REQUIRED TO HAVE REGISTERED 10.REFER TO INTERIOR ELEVATIONS&I.D.DRAWINGS FOR CABINET,COUNTER LENGTHS,DIMENSIONS,COUNTERTOP MATERIALS EXTENDS UP THE WALL AT LEAST 4 INCHES. SIGNAGE AS REQUIRED BY IBC SECTIONS 1111.1,1111.2 AND 1111.3 AND ICC/ANSI CH.7. HANDRAILS ON EACH SIDE. ARCHITECT AND DETAIL REFERENCES.FIELD VERIFY ALL DIMENSIONS. B. IN OTHER THAN DWELLING UNITS,WALLS AND PARTITIONS WITHIN 2 FEET OF URINALS AND WATER CLOSETS SHALL 6. EDGE PROTECTION:PROVIDED ON EACH SIDE OF RAMP RUNS AND RAMP LANDINGS " HAVE A HARD,NON-ABSORBENT SURFACE TO A HEIGHT OF 4 FEET ABOVE THE FLOOR.THE MATERIAL SHALL BE OF 6.THE FOLLOWING NOTES ARE PROVIDED AS A REFERENCE AND ARE NOT INTENDED TO BY EITHER A 12"EXTENDED FLOOR SURFACE PAST THE INSIDE FACE OF RAILING OR A TYPE THAT IS NOT ADVERSELY AFFECTED BY MOISTURE.TOILET ROOM ACCESSORIES PROVIDED ON OR W ITHIN REPLACE THE CODE.REFER THE REFERENCED CODES FOR COMPLETE TEXT AND FIGURES. BY CURB OR BARRIER WITHIN 4"OF THE FLOOR. B.SITE ISSUES WALLS SHALL BE INSTALLED AND SEALED TO PROTECT STRUCTURAL ELEMENTS FROM MOISTURE.(IBC SECTION B.BUILDING BLOCKS sFnTe aR wnswucTONM 1210.2.2) D. CURB RAMPS TO COMPLY WITH ICC A117.1-2009 SECTION 406 1.VERIFY GRADES SHOWN ON DRAWINGS PRIOR TO CONSTRUCTION. C. SHOWERS(IBC SECTION 1210.2.3)SHOWER COMPARTMENTS AND WALLS ABOVE BATHTUBS WITH INSTALLED 1. FLOOR SURFACE(ICC Al 17.1-2009 SECTION 302): E. ELEVATORS TO COMPLY WITH ICC At 17.1-2009 SECTION 407-409 SHOWER HEADS SHALL BE FINISHED WITH A SMOOTH,NON-ABSORBENT SURFACE TO A MINIMUM HEIGHT OF 70 A. SHALL BE STABLE,FIRM AND SLIP-RESISTANT. STAMP 2.ALL ROOF DOWNSPOUTS TO BE TIGHTLINED TO STORMWATER SYSTEM-SEE CIVIL AND LANDSCAPE DRAWINGS. INCHES ABOVE THE DRAIN INLET. B. CARPET SHALL HAVE A FIRM CUSHION,PAD OR BACKING OR NO CUSHION OR PAD. D. PRIVACY(IBC SECTION 1210.3)PRIVACY AT WATER CLOSETS AND URINALS SHALL BE PROVIDED IN ACCORDANCE CARPET SHALL HAVE A LEVEL LOOP,TEXTURED LOOP,LEVEL CUT PILE OR LEVEL E.SITE&BUILDING ELEMENTS: k 3.FIRE DEPT REQUIREMENT:VERIFY MIN.HEIGHT LETTERS,1/2"MIN.WIDTH LETTERS,CONTRASTING BACKGROUND,PLAINLY VISIBLE WITH SECTIONS 1210.3.1 AND 1210.3.2. CUT/UNCUT PILE TEXTURE.THE PILE SHALL BE 1/2"MAX.IN HEIGHT. - FROM THE STREET. C. OPENINGS IN FLOOR SURFACE SHALL NOT PERMIT THE PASSAGE OF 1/2"DIAM. 1. PARKING SPACES(ICC A117.1-2009 SECTION 502): s 5.MASONRY:ALL NON-STRUCTURAL FACING OF BRICK,CONCRETE,STONE,ETC.,SHALL BE GOVERNED BY THE SPHERE.ELONGATED OPENINGS SHALL BE PLACED WITH LONG DIRECTION A. SIZE:CAR:96"MINIMUM IN WIDTH VAN:132"MINIMUM IN WIDTH(MAY BE 96"MIN.IN e t C.MOISTURE CONTROL REQUIREMENTS OF IBC SECTION 1405. PERPENDICULAR TO DOMINANT DIRECTION OF TRAVEL. WIDTH WITH AN ADJACENT ACCESS AISLE WIDTH OF 96").VERTICAL CLEARANCE AT VAN STALL AND ROUTE TO/FROM STALL IS 98". o'� 1.EXTERIOR WALLS WEATHER PROTECTION(IBC SECTION 1403.2):THE EXTERIOR WALL SHALL PROVIDE WEATHER 6.PROTECTION AGAINST DECAY OR TERMITES(IBC SECTION 2304.12):PROVIDE NATURALLY DURABLE OR PRESERVATIVE- 2. CHANGES IN LEVEL(ICC Al 17.1-2009 SECTION 303): B. ACCESS AISLE:SHALL ADJOIN AN ACCESSIBLE ROUTE.MAY BE SHARED BETWEEN PROTECTION FOR THE BUILDING.THE MATERIALS OF THE MINIMUM NOMINAL THICKNESS SPECIFIED IN TABLE 1405.2 SHALL TREATED WOOD IN THE FOLLOWING LOCATIONS: A. CHANGES IN LEVEL OF 1/4"MAXIMUM IN HEIGHT ARE ALLOWED TO BE VERTICAL. TWO ACCESSIBLE SPACES.MIN.60"IN WIDTH AND EXTEND FULL LENGTH OF BE ACCEPTABLE AS APPROVED WEATHER COVERINGS. A. JOISTS,GIRDERS AND SUBFLOOR AND SUPPORTING FLOOR CONSTRUCTION:JOISTS OR WOOD STRUCTURAL B. CHANGES IN LEVEL GREATER THAN 1/4"AND NOT MORE THAN 1/2"MAXIMUM HEIGHT PARKING STALL THEY SERVE.MARKED TO DISCOURAGE PARKING IN THEM. R FLOORS CLOSER THAN 18 INCHES OR WOOD GIRDERS CLOSER THAN 12"TO THE EXPOSED GROUND IN CRAWL SHALL BE BEVELED WITH A SLOPE NOT STEEPER THAN 1:2. C. MAXIMUM SLOPE 1:48 k'a 2.VENTILATION(IBC SECTION 1203):BUILDINGS SHALL BE PROVIDED WITH NATURAL VENTILATION IN ACCORDANCE WITH SPACES OR UNEXCAVATED AREAS WITHIN THE PERIMETER FOUNDATION(IBC SECTION 2304.12.1.1) D. IDENTIFICATION:REQUIRED TO BE IDENTIFIED BY SIGNS INCLUDING THE rn o SECTION 1203.4,OR MECHANICAL VENTILATION IN ACCORDANCE WITH THE IMC. B. WOOD SUPPORTED BY EXTERIOR FOUNDATION WALLS:WOOD FRAMING MEMBERS,INCLUDING WOOD SHEATHING 3. TURNING SPACE(ICC Al 17.1-2009 SECTION 304): INTERNATIONAL SYMBOL OF ACCESSIBILITY(WHITE ON BLUE BACKGROUND(WA THAT REST ON EXTERIOR FOUNDATION WALLS AND ARE LESS THAN 8"FROM EXPOSED EARTH(IBC SECTION A. FLOOR SURFACE OF TURNING SPACE SHALL HAVE A SLOPE NOT STEEPER THAN 1:48. STATE AMEND.)VAN STALLS SHALL BE IDENTIFIED AS"VAN ACCESSIBLE."SIGNS 3.ATTIC SPACES(IBC SECTION 1203.2):ENCLOSED ATTICS AND ENCLOSED RAFTER SPACES FORMED WHERE CEILINGS ARE 2304.12.1.2) B. CIRCULAR:60"MIN.DIAMETER,PERMITTED TO INCLUDE KNEE&TOE CLEARANCE. SHALL BE MOUNTED 60"MIN.ABOVE THE SURFACE OF THE STALL TO THE BOTTOM APPLIED DIRECTLY TO THE UNDERSIDE OF ROOF FRAMING MEMBERS SHALL HAVE CROSS VENTILATION FOR EACH C. EXTERIOR WALLS BELOW GRADE:WOOD FRAMING MEMBERS ATTACHED DIRECTLY TO THE INTERIOR OF EXTERIOR C. T-SHAPED:REFER TO FIGURE 304.3. OF THE SIGN. SEPARATE SPACE BY VENTILATION OPENINGS PROTECTED AGAINST THE ENTRANCE OF RAIN AND SNOW. MASONRY OR CONCRETE WALLS BELOW GRADE(IBC SECTION 2304.12.1.3) D. DOORS ARE PERMITTED TO SWING INTO TURNING SPACE UNLESS OTHERWISE UNVENTED ATTIC ASSEMBLIES(SPACES BETWEEN CEILING JOISTS OF THE TOP STORY AND THE ROOF RAFTERS)ARE D. SLEEPERS AND SILLS ON A CONCRETE SLAB THAT IS IN DIRECT CONTACT WITH THE EARTH.(IBC 2304.12.1.4) SPECIFIED. 2. PASSENGER LOADING TO COMPLY WITH ICC At 17.1-2009 SECTION 503. PERMITTED ACCORDANCE WITH IBC SECTION 1203.3#4. E. POSTS OR COLUMNS SUPPORTING PERMANENT STRUCTURES AND SUPPORTED BY A CONCRETE SLAB OR FOOTING THAT IS IN DIRECT CONTACT WITH THE EARTH.(IBC SECTION 2304.12.2.2) 4. CLEAR FLOOR SPACE(ICC At 17.1-2009 SECTION 305): 5. WINDOWS(ICC At 17.1-2009 SECTION 506): c 4.VAPOR RETARDERS(IBC SECTION 1405.3)CLASS I OR CLASS II VAPOR RETARDERS SHALL BE PROVIDED ON THE INTERIOR F. THE PORTIONS OF GLU-LAMINATED TIMBERS THAT FORM STRUCTURAL SUPPORTS OF A BUILDING/STRUCTURE A. FLOOR SURFACE OF TURNING SPACE SHALL HAVE A SLOPE NOT STEEPER THAN 1:48 A. ACCESSIBLE WINDOWS SHALL HAVE OPERABLE PARTS PER ICC Al 17.1-2009 SIDE OF FRAME WALLS IN ZONES 5,6,7,8 AND MARINE 4.THE APPROPRIATE ZONE SHALL BE SELECTED IN ACCORDANCE AND ARE EXPOSED TO THE WEATHER SHALL BE PRESSURE TREATED WITH PRESERVATIVE OR NATURALLY (2%). SECTION 309.WITH CHAPTER 3 OF THE INTERNATIONAL ENERGY CONSERVATION CODE.MATERIAL VAPOR RETARDER CLASS SHALL BE DURABLE OR PRESERVATIVE-TREATED WOOD(IBC SECTION 2304.12.2.4) B. SIZE:30"X 48" ACCORDANCE WITH IBC 1405.3.2. G. WOOD STRUCTURAL MEMBERS SUPPORTING MOISTURE-PERMEABLE FLOORS OR ROOFS THAT ARE EXPOSED TO C. PERMITTED TO INCLUDE KNEE&TOE SPACE UNLESS OTHERWISE SPECIFIED. E.PLUMBING ELEMENTS&FACILITIES THE WEATHER,SUCH AS CONCRETE SLABS,SHALL BE OF NATURALLY DURABLE OR PRESERVATIVE-TREATED D. POSITIONED FOR EITHER A PARALLEL OR FORWARD APPROACH. 1. PLUMBING ELEMENTS AND FACILITIES REQUIRED TO BE ACCESSIBLE(OTHER THAN A. CLASS I:SHEET POLYETHYLENE,NONPERFORATED ALUMINUM FOIL WOOD UNLESS SEPARATED FROM SUCH FLOORS OR ROOFS BY AN IMPERVIOUS MOISTURE BARRIER.(IBC E. ONE FULL,UNOBSTRUCTED SIDE SHALL ADJOIN OR OVERLAP AN ACCESSIBLE WITHIN ACCESSIBLE DWELLING UNITS SHALL COMPLY WITH IBC SECTION 1109.2 B. CLASS II:KRAFT-FACED FIBERGLASS BATTS OR PAINT WITH A PERM RATING GREATER THAN 0.1 AND LESS THAN OR SECTION 2304.12.2.5) ROUTE. AND ICC At 17.1-2009 CHAPTER 6 WITH AMENDMENTS. EQUAL TO 1.0 H. NATURALLY DURABLE OR PRESERVATIVE-TREATED WOOD SHALL BE UTILIZED FOR THOSE PORTIONS OF WOOD F. IF POSITIONED IN AN ALCOVE,ADDITIONAL MANEUVERING CLEARANCES ARE 2. REFER TO ACCESSIBILITY DETAILS SHEET A550 FOR ACCESSIBLE WATER CLOSETS, C. CLASS III:LATEX OR ENAMEL PAINT.(CLASS III VAPOR RETARDERS SHALL BE PERMITTED PER IBC TABLE 1405.3.2. MEMBERS THAT FORM THE STRUCTURAL SUPPORTS OF BUILDINGS,BALCONIES,PORCHES OR SIMILAR WHICH ARE REQUIRED. LAVATORIES,URINALS,DRINKING FOUNTAINS,BATHTUBS AND GRAB BARS. EXPOSED TO WEATHER.(IBC SECTION 2304.12.2.3) 5. AIR LEAKAGE(WSEC SECTION C402.5)THE THERMAL ENVELOPE OF BUILDINGS SHALL COMPLY WITH SECTIONS 5. KNEE AND TOE CLEARANCES(ICC A117.1-2009 SECTION 306):WHERE SPACE C402.5.1 THROUGH C402.5.8. 7.GYPSUM CONSTRUCTION(IBC 2508) BENEATH AN ELEMENT IS INCLUDED AS PART OF A CLEAR FLOOR SPACE, m A. GYPSUM BOARD SHALL BE INSTALLED IN COMPLIANCE WITH ASTM C 840&GA 216,GYPSUM SHEATHING:ASTM C CLEARANCE OR TURNING SPACE IT SHALL COMPLY AS FOLLOWS: o 6.RECESSED LIGHTING FIXTURES(WSEC SECTION C402.5.8)RECESSED LUMINARIES INSTALLED IN THE BUILDING THERMAL 1280.(IBC TABLE 2508.1) A. TOE CLEARANCE:SPACE BENEATH AN ELEMENT BETWEEN THE FLOOR AND 9" ENVELOPE SHALL BE SEALED TO LIMIT AIR LEAKAGE BETWEEN CONDITIONED AND UNCONDITIONED SPACES.ALL B. GYPSUM WALLBOARD OR GYPSUM PLASTER SHALL NOT USED IN ANY EXTERIOR SURFACE WHERE EXPOSED TO ABOVE THE FLOOR;17"MIN/25"MAX.DEPTH UNDER AN ELEMENT;30"MIN.IN WIDTH. F.COMMUNICATION FEATURES n RECESSED LUMINARIES SHALL BE IC-RATED AND LABELED AS HAVING AN AIR LEAKAGE RATE OF NOT MORE THAN 2.0 CFM THE WEATHER.GYPSUM SHEATHING SHALL BE INSTALLED ON EXTERIOR SURFACES IN ACCORDANCE WITH ASTM C B. KNEE CLEARANCE:SPACE BENEATH AN ELEMENT BETWEEN 9"AND 27"ABOVE THE 1. ALARMS(ICC A117.1-2009 SECTION 702):PROVIDE ACCESSIBLE AUDIBLE AND VISUAL WHEN TESTED IN ACCORDANCE WITH ASTM E 283 AT A 1.57 PSF PRESSURE DIFFERENTIAL.ALL RECESSED LUMINARIES 1280.(IBC SECTION 2508.2) FLOOR;11"MIN/25"MAXIMUM DEPTH UNDER AN ELEMENT AT 9"ABOVE THE FLOOR. ALARMS AND NOTIFICATION APPLIANCES INSTALLED IN ACCORDANCE WITH NFPA SHALL BE SEALED WITH A GASKET OR CAULK BETWEEN THE HOUSING AND INTERIOR WALL OR CEILING COVERING. C. GYPSUM WALLBOARD,GYPSUM LATH OR GYPSUM PLASTER SHALL NOT BE INSTALLED UNTIL WEATHER 8"MIN.IN DEPTH AT 27"ABOVE THE FLOOR.BETWEEN 9"AND 27"THE KNEE 72,POWERED BY A COMMERCIAL LIGHT AND POWER SOURCE,BE PERMANENTLY PROTECTION FOR THE INSTALLATION IS PROVIDED.(IBC SECTION 2508.2.1) CLEARANCE MAY BE REDUCED AT A RATE OF 1"FOR EACH 6"IN HEIGHT;30"MIN.IN CONNECTED TO THE WIRING OF THE PREMISES ELECTRIC SYSTEM,AND BE 8.AIR BARRIER(WSEC SECTION C402.5.1)A CONTINUOUS AIR BARRIER SHALL BE PROVIDED THROUGHOUT THE BUILDING D. WHEN APPLIED DIRECTLY ON FRAMING,ALL EDGES AND ENDS OF GYPSUM WALLBOARD IN SINGLE-PLY WIDTH. PERMANENTLY INSTALLED. THERMAL ENVELOPE.THE AIR BARRIERS SHALL BE PERMITTED TO BE LOCATED ON THE INSIDE OR OUTSIDE OF THE APPLICATIONS SHALL OCCUR ON THE FRAMING MEMBERS,EXCEPT THOSE EDGES WHICH ARE PERPENDICULAR TO 2. SIGNAGE(ICC At 17.1-2009 SECTION 703):INTERIOR AND EXTERIOR SIGNS g BUILDING ENVELOPE,LOCATED WITHIN THE ASSEMBLIES COMPOSING THE ENVELOPE,OR ANY COMBINATION THEREOF. THE FRAMING(IBC SECTION 2508.3) 6. PROTRUDING OBJECTS(ICC At 17.1-2009 SECTION 307)ON CIRCULATION PATHS: IDENTIFYING PERMANENT ROOMS AND SPACES SHALL BE TACTILE.(IBC 2015 THE AIR BARRIER SHALL COMPLY WITH SECTION C402.5.1.1 AND C402.5.1.2. E. WOOD SUPPORTS FOR GYPSUM WALLBOARD SHALL BE NO LESS THAN 2"NOMINAL IN THE SMALLEST DIMENSION, A. OBJECTS WITH LEADING EDGES MORE THAN 27"AND NOT MORE THAN 80"ABOVE APPENDIX E107.2)TACTILE CHARACTER SHALL BE DUPLICATED IN BRAILLE. € EXCEPT THAT 1"NOMINAL BY 2"NOMINAL FURRING STRIPS MAY BE USED OVER SOLID BACKING.(IBC SECTION THE FLOOR SHALL PROTRUDE 4"MAXIMUM INTO THE CIRCULATION PATH. SIGNAGE SHALL COMPLY WITH ICC/ANSI SECTION 703. 2504.1.1). B. GUARDRAILS OR OTHER BARRIERS SHALL BE PROVIDED WHERE OBJECT PROTRUDE 3. TWO-WAY COMMUNICATION(IBC APPENDIX SECTION E105.6):WHERE TWO-WAY a D.HAZARD F. GLASS MAT WATER-RESISTANT GYPSUM BACKING PANELS,DISCRETE NONASBESTOS FIBER-CEMENT INTERIOR GREATER THAN 4"AND/OR WHERE THE VERTICAL CLEARANCE IS LESS THAN 80" COMMUNICATION SYSTEMS ARE PROVIDED TO GAIN ADMITTANCE TO THE zo SUBSTRATE SHEETS OR NONASBESTOS FIBER-MAT REINFORCED CEMENT SUBSTRATE SHEETS(ASTMC 1178,C1288 ABOVE THE FLOOR.THE LEADING EDGE OF SUCH BARRIER SHALL BE 27"MAXIMUM BUILDING,THE SYSTEM SHALL COMPLY WITH ICC/ANSI 708. OR C1325)INSTALLED IN ACCORDANCE WITH MANUFACTURER RECOMMENDATIONS SHALL BE USED AS A BASE FOR ABOVE THE FLOOR. 1.GUARDS(IBC SECTION 1015) WALL TILE IN TUB AND SHOWER AREAS AND WALL AND CEILING PANELS IN SHOWER AREAS.WATER RESISTANT C. PROTRUDING OBJECTS SHALL NOT REDUCE THE REQUIRED CLEAR WIDTH OF GYPSUM BACKING BOARD SHALL BE USED AS A BASE FOR TILE IN WATER CLOSET COMPARTMENT WALLS(ASTM C ACCESSIBLE ROUTES. A. SHALL BE LOCATED ALONG OPEN SIDED WALKING SURFACES THAT ARE LOCATED MORE THAN 30 INCHES TO 840,GA-216).REGULAR GYPSUM WALLBOARD IS PERMITTED UNDER TILE OR WALL PANELS IN OTHER CEILING w FLOOR OR GRADE BELOW.GUARDS SHALL BE NO LESS THAN 42 INCHES IN HEIGHT,EXCEPT THAT WITHIN AREAS.(IBC SECTION 2509.2) 7. REACH RANGES(ICC At 17.1-2009 SECTION 308): INDIVIDUAL UNITS OF R-2 OCCUPANCIES,WHERE THE TOP OF THE GUARD ALSO SERVES AS A HANDRAIL ON THE G. WATER RESISTANT GYPSUM BACKING BOARD SHALL NOT BE USED OVER A VAPOR RETARDER IN SHOWER OR A. FORWARD REACH:WHERE FORWARD REACH IS UNOBSTRUCTED,THE HIGH REACH OPEN SIDE OF STAIRS,THE TOP OF THE GUARD SHALL HAVE A HEIGHT NOT LESS THAN 34"MIN.AND NOT MORE BATHTUB COMPARTMENTS,IN DIRECT EXPOSURE TO WATER OR AREAS SUBJECT TO HIGH HUMIDITY OR ON SHALL BE 48"MAXIMUM AND LOW REACH SHALL BE 15"MINIMUM ABOVE THE FLOOR. G> THAN 38"MAX.IN HEIGHT(IBC SECTION 1013.2,EXCEPTION 2).GUARDS SHALL NOT HAVE OPENINGS WHICH ALLOW CEILINGS WHERE FRAMING EXCEED 12"O.C.FOR 1/2"BOARD OR 16"O.C.FOR 5/8"BOARD.(IBC SECTION 2509.3) WHERE HIGH FORWARD REACH IS OVER AN OBSTRUCTION,THE CLEAR FLOOR PASSAGE OF A SPHERE 4 INCHES IN DIAMETER(IBC SECTION 1015.2). SPACE SHALL EXTEND BENEATH THE ELEMENT FOR A DISTANCE NOT LESS THAN THE E B. MECHANICAL EQUIPMENT/ROOF HATCHES:GUARDS SHALL BE PROVIDED WHERE MECHANICAL EQUIPMENT OR REQUIRED REACH DEPTH.WHERE THE REACH DEPTH IS 20"MAXIMUM,THE HIGH ROOF HATCH IS LOCATED WITHIN 10 FEET OF A ROOF EDGE OR OPEN SIDE OF A WALKING SURFACE LOCATED G.MISCELLANEOUS REACH SHALL BE 48"MAXIMUM.WHERE THE REACH DEPTH IS GREATER THAN 20"TO go MORE THAN 30 INCHES ABOVE THE FLOOR,ROOF OR GRADE BELOW.GUARDS MUST PREVENT THE PASSAGE OF A 25"MAX.,THE HIGH REACH SHALL BE 44"MAXIMUM. €o SPHERE 21"IN DIAMETER AND EXTEND NOT LESS THAN 30"BEYOND THE EACH END OF THE EQUIPMENT(IBC 1.PROVIDE BLOCKING AT ALL ENTRANCE DOOR KNOB STRIKER POINTS. B. SIDE REACH:WHERE CLEAR FLOOR SPACE ALLOWS A PARALLEL APPROACH TO AN SECTION 1015.6). 2.PROVIDE BACKING TO 12"ON BOTH SIDES OF WINDOWS FOR INSTALLATION OF DRAPERIES. ELEMENT,AND THE SIDE REACH IS UNOBSTRUCTED,THE HIGH REACH SHALL BE 48" Q 3 c LL 3.PROVIDE BLOCKING AT SHOWER CURTAIN RODS AND SHOWER SEATS. MAXIMUM AND LOW REACH SHALL BE 15"MINIMUM ABOVE THE FLOOR.WHERE THEIT 1 2.SAFETY GLAZING(IBC SECTION 2406)IS REQUIRED IN HAZARDOUS LOCATIONS.REFER TO WINDOW SCHEDULE SHEET 4.PROVIDE BLOCKING FOR ALL WALL MOUNTED ACCESSORIES AND LIGHT FIXTURES. HIGH SIDE REACH IS OVER AN OBSTRUCTION,THE HEIGHT OF THE OBSTRUCTION w A700 FOR SPECIFIC LOCATIONS. SHALL BE 34"MAXIMUM AND THE DEPTH SHALL BE 24"MAXIMUM.THE HIGH SIDE y a o 5.PROVIDE BLOCKING FOR ALL WALL MOUNTED DOOR STOPS. L3 6.PROVIDE BLOCKING FOR ALL GRAB BARS. REACH SHALL BE 48"MAXIMUM FOR A REACH DEPTH OF 10"AND 46"MAXIMUM>10" w' e E.FIRE SAFETY ISSUES 7.PROVIDE BLOCKING FOR ALL WALL MOUNTED AND RECESSED CABINETS. TO 24"MAXIMUM REACH DEPTH. 8.INSTALL WOOD BACKING/BLOCKING IN METAL FRAMING FOR HANDRAILS,MILLWORK,CABINETS AND WINDOW&DOOR o°' rc FRAMES. 8. OPERABLE PARTS(ICC Al 17.1-2009 SECTION 309): L w' w g 3 1.PORTABLE FIRE EXTINGUISHERS(IBC SECTION 906): 9.PROVIDE VENTILATION&EXHAUST IN ACCORDANCE WITH INTERNATIONAL MECHANICAL CODE TABLE 403.3.1.1. A. A CLEAR FLOOR SPACE SHALL BE PROVIDED AT OPERABLE PARTS. /0� ul z U FOR BUILDINGS UNDER CONSTRUCTION PROVIDE PORTABLE FIRE EXTINGUISHERS PER SECTION 3315 OF THE A. PROVIDE SOURCE SPECIFIC EXHAUST VENTILATION SYSTEM(IMC 403.8.4)FOR KITCHEN,BATHROOM,WATER B. OPERABLE PARTS SHALL BE LOCATED WITH REACH RANGES. V NZi w-w 3� j� INTERNATIONAL FIRE CODE. CLOSET AND LAUNDRY AREA.DUCTS TO TERMINATE OUTDOORS. SHALL BE OPERABLE WITH ONE HAND AND SHALL NOT REQUIRE TIGHT w CL < iw N FOR GROUPS A,B,M,R-2,S-2 OCCUPANCIES PROVIDE PORTABLE FIRE EXTINGUISHERS SELECTED,INSTALLED AND MAINTAINED B. CLOTHES DRYER LENGTH(IMC 504.6.4.1 WA.STATE):THE MAXIMUM LENGTH OF THE EXHAUST DUCT SHALL BE 35 GRASPING,PINCHING OR TWISTING OF THE WRIST.THE FORCE REQUIRED TO o ml IN ACCORDANCE WITH IBC SECTION 906.2 AND NFPA 10.ORDINARY HAZARD OCCUPANCY:2-A RATED EXTINGUISHER,MAX. FEET FROM THE CONNECTION TO THE TRANSITION DUCT FROM THE DRYER TO THE OUTLET TERMINAL.WHERE ACTIVATE OPERABLE PARTS SHALL NOT EXCEED 5.0 POUNDS. ¢ w cj a o ZI C TRAVEL 75 FEET(IBC TABLE 906.3(1))SEE PLAN FOR LOCATIONS OF 2A 10BC FIRE EXTINGUISHERS. FITTINGS ARE USED REDUCTIONS IN LENGTH SHALL BE PER IMC TABLE 504.6.4.1. THE MAXIMUM LENGTH OF THE w Z DUCT MAYBE INCREASED IN AN ENGINEERED EXHAUST SYSTEM WHEN A LISTED AND LABELED EXHAUST .ACCESSIBLE ROUTE OF TRAVEL Q r 3 0�A- w 3 LL 55 Ow 2.FIRE ALARM&DETECTION SYSTEMS(IBC SECTION 907.2.9)PROVIDE FIRE ALARM AND DETECTION SYSTEM DESIGNED, BOOSTER FAN IS INSTALLED IN ACCORDANCE WITH THE MANUFACTURER'S INSTALLATION INSTRUCTIONS. 1. ACCESSIBLE ROUTE(IBC SECTION 11041 INSTALLED&MAINTAINED IN ACCORDANCE W/NFPA 72.FOR GROUP R-2,A MANUAL FIRE ALARM SYSTEM THAT ACTIVATES C. EXHAUST OUTLETS FOR ENVIRONMENTAL AIR(IMC 501.2)SHALL BE LOCATED WITH THE FOLLOWING MINIMUM A. SITE ARRIVAL POINTS(IBC SECTION 1104.1):ACCESSIBLE ROUTES WITHIN THE SITE UI THE OCCUPANT NOTIFICATION SYSTEM IN ACCORDANCE WITH IBC SECTION 907.5 SHALL BE INSTALLED.FIRE ALARM DISTANCES:3 FT TO PROPERTY LINES,3 FT.TO OPERABLE OPENINGS AND 10 FT.TO MECHANICAL AIR INTAKES. SHALL BE PROVIDED FROM PUBLIC TRANSPORTATION STOPS;ACCESSIBLE PARKING, CONTRACTOR SHALL VERIFY&MEET ALL REQUIREMENTS FOR FIRE ALARMS&SMOKE DETECTORS AND SHALL SUBMIT A ACCESSIBLE LOADING ZONES AND PUBLIC STREETS OR SIDEWALKS TO THE E2 FIXTURE SCHEDULE AND DRAWINGS FOR FIRE ALARM SYSTEM TO FIRE AUTHORITY FOR APPROVAL.FIRE ALARM SUB- Q CONTRACTOR IS RESPONSIBLE FOR OBTAINING NECESSARY PERMIT(s). BUILDING ENTRANCE SERVED. E B. WITHIN A SITE(IBC SECTION 1104.2):AT LEAST ONE ACCESSIBLE ROUTE SHALL (j 3.CONCEALED SPACES(IBC SECTION 718)PROVIDE FIREBLOCKING PER IBC SECTION 718.2.PROVIDE FLOOR CONNECT ACCESSIBLE BUILDINGS,ACCESSIBLE FACILITIES,ACCESSIBLE ELEMENTS DRAFTSTOPPING PER IBC SECTION 718.3.PROVIDE ATTIC DRAFTSTOPPING PER IBC SECTION 718.4.REFER TO SHEET A051 AND ACCESSIBLE SPACES THAT ARE THE SAME SITE. 3 FOR NOTES AND DETAILS. C. CONNECTED SPACES(IBC SECTION 1104.3):WHEN A BUILDING OR PORTION OF O BUILDING IS REQUIRED TO BE ACCESSIBLE,AN ACCESSIBLE ROUTE SHALL BE LL PROVIDED TO EACH PORTION OF THE BUILDING,TO ACCESSIBLE BUILDING N ENTRANCES CONNECTING ACCESSIBLE PEDESTRIAN WALKWAYS AND THE PUBLIC WAY. y D. LOCATION(IBC SECTION 1104.5):ACCESSIBLE ROUTES SHALL BE LOCATED IN THE SAME AREA AS GENERAL CIRCULATION PATH. W E. ACCESSIBLE ENTRANCES(IBC SECTION 1105):60%OF PUBLIC ENTRANCES ARE E REQUIRED TO BE ACCESSIBLE. 0 REFER TO THE ARCHITECTURAL SITE PLAN A020 FOR DESIGNATED ACCESSIBLE PROJECT#: 1827 X ROUTES OF TRAVEL AND ACCESSIBLE ENTRANCES. DRAWN BY: JH 4 g 2. ACCESSIBLE ROUTES SHALL CONTAIN ONE OR MORE OF THE FOLLOWING CHECKED BY: ST y COMPONENTS(ICC ANSI A117.1-2009,402.2): N � A. WALKING SURFACE(ICC A117.1-2009 SECTION 403): GENERAL AND 1. SLOPE:SHALL HAVE A RUNNING SLOPE NOT STEEPER THAN 1:20(5%)AND CROSS ACCESSIBILITY NOTES (j SLOPE NOT STEEPER THAN 1:48(2%). 2. CLEAR W IDTH: THE MINIMUM CLEAR WIDTH OF AN ACCESSIBLE ROUTE OF TRAVEL SHALL BE 32"WIDTH FOR LENGTH</=24"AND 36"WIDTH FOR LENGTH>/=24". EXTERIOR ROUTES SHALL HAVE CLEAR WIDTH C UD IBC 110 DE RE STATE O 0 AMENDMENT).WHERE AN ACCESSIBLE ROUTE INCLUDES A 180 DEGREE TURN AROUND AN OBJECT THAT IS LESS THAN 48 INCHES IN WIDTH,CLEAR WIDTHS SHALL M BE 42 INCHES APPROACHING THE TURN,48"MINIMUM DURING THE TURN,AND 42" z LEAVING THE TURN.IF CLEAR WIDTH AT TURN IS 60"MINIMUM,36"WIDE ROUTE IS PERMIT SET 10/09/2020 w ALLOWED. LL 3. PASSING SPACE:AN ACCESSIBLE ROUTE WITH A CLEAR WIDTH LESS THAN 60" SHALL PROVIDE A 60"X 60"PASSING SPACE AT INTERVALS OF 2D0'MAXIMUM.