Laserfiche WebLink
FREIHEIT <br /> ARCHITECTURE <br /> NOTE:VIEW OF LOUVERNJINDOW FROM INTERIOR <br /> INSTALL WEATHER <br /> RESISTIVE BARRIER <br /> FROM BELOW <br /> INSTALL 3/8"WIDE-------------- <br /> SS METAL SILL PAN <br /> SEALANT JOINT(MINIMUM) 9" <br /> WITH BACKER ROD <br /> AROUND INTERIOR ..I..:r:. <br /> PERIMETER OF <br /> LOUVER/WINDOW J <br /> AT HEAD,JAMBS,AND SILL 18" <br /> 1T W <br /> \ Q\ <br /> 2" O <br /> AT SILL,INSTALL SET SILL PAN IN BEAD \ �:.I <br /> SEALANTBETWEEN CUT PENETRATION OF <br /> BACKDAM OF SILL FLASHING AND FOLD SEALANT AS SHOWN, �. U. W <br /> PAN THROUGH ROUGH SLOPE [� <br /> AND LOUVER OPENING,MINIMUM 2" PAN TO DRAIN <br /> W <br /> 70 FLASHING STEP J FLASHING STEP G FLASHING STEP D 1 FLASHING STEP A '~/1 <br /> A6.01 " 1 1 I 1 vJ <br /> Scale.1/4"=1'-0 A6.01 Scale:1/4"=1'-0" A6.01 Scale:I-.=1'-.. A6.01 Scale:114"=1'-01. <br /> Z <br /> Q <br /> O <br /> ATTACH PENETRATION >_ <br /> FLASHING TO ROUGH Q <br /> OPENING >> M <br /> AT INTERIOR FACE OF p <br /> PENETRATION CUT FRAMING z N <br /> VERIFY HEIGHT OF BACK FLASHING, PEJM NETRATION = LLI 00 <br /> 8,END DAMS WITH FOLD FLASHING AND w <br /> INSTALL METAL WINDOW THROUGH FOLD Q <br /> HEAD MANUFACTURER ROUGH THROUGH ROUGH > <br /> FLASHING,SEE INSTALL SHIMS BETWEEN OPENING, OPENING, <br /> DETAIL SILL PAN AND SILL MINIMUM 2" MINIMUM 2" <br /> 0 LLI <br /> 13 FOR TYPICAL CLOSURE FLASHING.SET 9" EXTEND > <br /> HEAD SILL PAN IN BED OF PENETRATION <br /> FLASHING DETAILS SEALANT FLASHING 12" LL.I W <br /> COORDINATE W/DEPTH <br /> OF ADJACENT BUILDING ?• ROUGH 12 O Lu <br /> METALFINISHS ILL PAN TO EACH OPENING AT 9" T Oro w <br /> MATCH ADJACENT 1 <br /> END OF SILL <br /> WINDOW FINISH.DO NOT <br /> PENETRATE HORIZONTAL <br /> SURFACES W/ BUTTERFLY BOTTOM <br /> FASTENERS • �2• <br /> CORNERS <br /> py 78• <br /> �'l SET HEAD �8• <br /> HEMMED EDGE FLASHING IN <br /> BEAD OF SEALANT <br /> AS NOTE:G.C.TO COORDINATE SEQUENCING& Y <br /> SHOWN INSTALLATION WITH ALL TRADES <br /> 11 FLASHING STEP K FLASHING STEP H FLASHING STEP E 2 FLASHING STEP B <br /> A6.01 Scale:1/4"=1'-0" A6".01 Scale:1/4"=V-0" / A6".01 1 Scale:1/4"=V-0" A8.01 Scale:1/4"=1'-0" <br /> �a <br /> F <br /> STERED <br /> ITECT <br /> MICHAEL J. L TON <br /> STATE OF WASHINGTON <br /> PENETRATION ISSUE LIST <br /> >,- FLASHING PERMIT SUBMITTAL 03.31.2022 <br /> INSTALL WEATHER \ CORNER BOOTS, PENETRATION PRICING UPDATE 08.09.2022 <br /> RESISTIVE BARRIER FLASHING "• <br /> FROM ABOVE OVER BUTTERFLY CORNER BOOTS, 1 BLDG REVISION 09.30.2022 <br /> HEADAND JAMB NOTNERS IF BUTTERFLY <br /> FLASHING, INSIDE 2 PW REVISION 10.04.2022 <br /> HORIZONTAL PREFORMED CORNERS IF 3 PLANNING/PW REVISION 11.23.2022 <br /> LAPS TO BE 6" NOT <br /> MINIMUM, CLOSURE FLASHINGS SET IN PREFORMED <br /> VERTICAL LAPS TO \ SEALANT.APPLY ROD AND <br /> BE SEALANT BETWEEN WINDOW 9• <br /> 12"MINIMUM \\ AND CLOSURE FLASHING <br /> } 9• <br /> WEATHER RESISTIVE \\\ WALUGL WALL SYSTEM 9" g,. <br /> BARRIER FROM PER MANUFACUFAC TURER'S <br /> BELOW SPECIFICATIONS.IF <br /> \ MANUFACTURER'S 9" N <br /> \\ INSTALLATION REQUIREMENTS <br /> DIFFER NOTIFY ARCHITECT OF <br /> DISCREPANCIES 9• <br /> 9+ <br /> NOTE:PROVIDE NON-CONTINUOUS SHIMS AT SILL.PROVIDE SEALANT AT 8 <br /> CONTINUOUS SHIM BOTTOM AND 9.4 <br /> BEHIND HEAD AND JAMB IF REQUIRED BY MANUFACTURER. OUTSIDE EDGES <br /> 1z FLASHING STEP L g FLASHING STEP I 6 FLASHING STEP F 3 FLASHING STEP C WINDOW <br /> FLASHING <br /> As.01 Scale:1/4"=1'-0" A6.01 Scale: 1/4"=V-O" A6.01 Scale: 1/4"=V-O" A6.01 Scale:1/4"=V-0" SEQUENCE <br /> A6.01 <br />