9532 7TH AVE SE 2025-09-16 - Laserfiche WebLink

Cover Plate Finishes0) - Standard Finishes Special Application Finishes White Polyester Off White Paint Black Paint Raw Brass Chrome Plated Bright Brass Finished Bronze Black Plated Satin Chrome Stainless Steel Clad(3) Custom Color Paint(2) Notes: 1. Paint or any other coating applied over the factory finish will void all approvals and warranties. 2. Custom color paint is semi-gloss,unless specified otherwise. 3. Stainless steel clad cover plates are Type 316 Stainless Steel on the finished side and C102 Copper Allow on the back side.Cover plates are not listed or approved as corrosion resistant. Installation Dimensions Recommended Min.to Min.to Max. Sprinkler Cover Cover Plate Hole Diameter Cover Plate Max. Face Dropped Deflector Cover Plate Plate Diameter Adjustment of Fitting to Distance below Temperature Model Model inch(mm) in Ceiling inch(mm) Ceilings') Ceiling Rating inch(mm) inch(mm) inch(mm) RFC30, G5 3-5/16 2-5/8 1/2 1-1/2 to 2 1/2 to 1 135°F RFC30LL (84) (67) (13) (38 to 51) (13 to 25) (57°C) RFC43, 135°F(2) RFC43LL, 3-5/16 2-5/8 1/2 1-1/2 to 2 1/2 to 1 (57°C) RFC49, G5 (84) (67) (13) (38 to 51) (13 to 25) or 165°F RFC49LL (74°C) RFC58, G5 3-5/16 2-5/8 3/4 1-1/2 to 2-1/4 1/4 to 1 13oor 1655E 3C) RFC76 (84) (67) (19) (38 to 57) (6 to 25) (74°C) Notes: 1. Face of fitting to ceiling dimensions are based on a nominal thread make up.Verify dimensions based on fitting and thread sealing method prior to installation.A 1/2"x 112"brass nipple extension(Reliable P/N 6999991900)is available where necessary for replacement of existing sprinklers. 2. For use with 165T(74°C)temperature rated sprinklers where the maximum ceiling temperature does not exceed 100°F(38°C). 3. For use with 212T(100°C)temperature rated sprinklers where the maximum ceiling temperature does not exceed 150T(66°C). Installation Model RFC series sprinklers are intended to be installed in Note:When used with gasketed fittings,follow fitting accordance with NFPA 13, NFPA 13R,or NFPA 13D,as well as manufacturer's installation instructions regarding tightening to the requirements of applicable authorities having jurisdiction. achieve a leak-free connection. Model RFC series sprinklers must not be installed in ceilings with positive pressure in the space above. Ensure that the 4 slots in Do not exceed the maximum recommended torque. Exceeding the cup are open and unobstructed following installation. Model the maximum recommended torque may cause leakage or RFC series sprinklers are shipped with a wrench-able protective impairment of the sprinkler. Use care when inserting or removing cap that should remain on the sprinkler until the sprinkler system the wrench from the sprinkler to avoid damage to the sprinkler. is placed in service following construction. Install the cover plate by hand by pushing the cover plate into the Model RFC series sprinklers can be installed without removing cup and turning the cover in the clockwise direction until it is tight the wrench-able protective cap using the Model W3 wrench. against the ceiling. Alternatively, Model RFC series sprinklers can be installed using the Model FC wrench by temporarily removing the protective cap during installation of the sprinkler.The use of any other wrench to installed Model RFC series sprinklers is not permitted and may damage the sprinkler. Fully insert the Model W3 wrench over the cap until it reaches the bottom of the cup,or the Model FC wrench over the sprinkler until the wrench engages the body. Do not wrench any other part of the sprinkler/cup assembly.The Model W3 and FC wrenches are designed to be turned with a standard 1/2"square drive.Tighten the sprinkler into the fitting after applying a PTFE based thread sealant to the sprinkler's threads. Recommended installation torque for iron pipe fittings is 8 to 18 ft-Ibs(11 to 24 N-m)for 1/2"thread sprinklers and 14 to 20 ft-Ibs(19 to 27 N-m)for 3/4"thread sprinklers. Bulletin 006 Reliable Page 7 of 8 June 2021 www.reliablesprinkler.com