6801 SEAWAY BLVD 2024 MCKESSON CORP 2025-09-12

Option Cards Kidde VS Series panels are supported by a complete line of mod- RZI16-2 Remote Zone Interface Module ules and related equipment that enhance performance and extend system capabilities. Option cards plug directly into the control :a_ panel main circuit board or are connected to it with a ribbon cable.After installation,terminals remain accessible.The cabinet pro-vides ample room for wire routing, keeping wiring neat at all times. o Single and Dual Loop Controller Cards The RZI16-2 Addressable Remote Zone Interface Module is an The V-SLC2-1 is a single loop controller card that can be used addressable device that provides connections for sixteen Class B with the VS1 as a replacement for the standard 64-point loop, or Initiating Device Circuits and two Class B Supervised Output with the VS4 as a 250-point expansion module. Circuits.The inputs and outputs can be configured individually for The V-SLC2-2 is a 500-point dual loop controller card for the VS4 several device types. that provides two IDC circuits, each with 125 detector addresses The RZI16-2 requires 18 consecutive addresses on the Signaling and 125 module addresses. Line Circuit(SLC).Addresses are assigned electronically.There are no address switches to set. Specifications V-SLC2-1 V-SLC2-2 Device Addresses VS4:one loop,250 VS4:two loops,500 The RZI16-2 incorporates two 8-segment DIP switches that are device addresses device addresses used to select the Alarm or Supervisory default device type for VS1:64 addresses each of the 16 IDC circuits.The module also includes one 4-seg- Wiring Class B or Class A ment DIP switch used to select the default Relay or NAC output Operating Voltage 24 VDC device type. Device types other than the default are accomplished Operating Current Standby:55 mA Standby:45 mA through programming. (fully loaded loop) Alarm:80 mA Alarm:70 mA Note:These ratings do not include the use of two-wire smoke modules. RZI16-2 Specifications Communication Line Max.20.6 V peak-to-peak Voltage Voltage 24V/Aux nominal: 24 VDC Terminal Rating 12 to 18 AWG(0.75 to 2.5 mmz) Supervisory current: 250 mA at 24 VDC nominal Alarm current: 1000 mA Circuit Current 0.5 A max. 24V/Aux minimum: 18.4 VDC Max total loop 66 Q 24V/Aux maximum: 26.4 VDC resistance NAC1, NAC2 nominal: 24 VDC Max total loop 0.5 uF Current capacitance Standby current Isolators 64 isolators maximum per loop(total both for 4.7 k EOL(U.S.) 4.8 mA/circuit isolator bases and modules) Standby current for Ground Fault 0 to 5 kn 3.9 k EOL(Canada) 5.7 mA/circuit Impedance Alarm current Operating 32 to 120°F(0 to 49°C) at nominal voltage 31.1 mA/circuit Environment 0 to 93%noncondensing at 90°F(32°C) Relay outputs Quantity 2 Type Rating(pilot duty) Programmable 24 VDC at 2.5 A Input circuit wiring 25 D per wire SA-ETH Ethernet Interface Card resistance SA-ETH wiring The SA-ETH card provides a Initiating device circuits To network standard 10/100 Base T Ether- Quantity 16 Network cable fg connection net network connection for EOL resistor 4.7 1<4(U.S.);3.9 1<4 Canada connecting to an intranet,a local Zone voltage 22.78 V for 4.7 kO(U.S.) I network, or the Internet.The 22.08 V for 3.9 kO(Canada) + card can be used to download Alarm current 31.1 mA/channel at nominal voltage Alarm impedance range <680 f2 0l�lf� configuration programming from Trouble impedance range >5.55 kf2 ° ® the VS-CU to the panel. Supervised output circuits ❑n The Ethernet card is installed on EOL resistor 15<0 ® the plastic assembly and con- Quantity 2 ® Short circuit detection <2.6 kf2 nects to the main circuit board Open circuit detection >61.9 k0 Ethernet card via a ribbon cable. Contact ratings 24 VDC at 2.5 A(5 A for two NACs) SA-ETH specifications Compatible cabinets MFC(A),VS4,APS Ethernet 10/100 Base T Operating environment Temperature 32 to 120°F(0 to 49°C) Humidity 0 to 93%RH,noncondensing at 90°F (32°C) Page 5 of 8 DATA SF. V85005-0135 Not to be used for instz Issue 1