My WebLink
|
Help
|
About
|
Sign Out
Home
Browse
Search
3003 W CASINO RD 2025 BLDG 40-53 Plans 2025-08-19
>
Address Records
>
W CASINO RD
>
3003
>
BLDG 40-53
>
Plans
>
3003 W CASINO RD 2025 BLDG 40-53 Plans 2025-08-19
Metadata
Thumbnails
Annotations
Entry Properties
Last modified
8/19/2025 12:00:53 PM
Creation date
8/19/2025 12:00:39 PM
Metadata
Fields
Template:
Address Document
Street Name
W CASINO RD
Street Number
3003
Tenant Name
BLDG 40-53
Permit
FA2501-007
Year
2025
Notes
MONITOR WF AND TAMPER SWITCH WITH EXISTING FIRE ALARM
Address Document Type
Plans
Imported From Microfiche
No
There are no annotations on this page.
Document management portal powered by Laserfiche WebLink 9 © 1998-2015
Laserfiche.
All rights reserved.
/
6
PDF
Print
Pages to print
Enter page numbers and/or page ranges separated by commas. For example, 1,3,5-12.
After downloading, print the document using a PDF reader (e.g. Adobe Reader).
View images
View plain text
(E) POTTER VS R <br /> The Symbol of Protection Vane Type Waterflow Alarm Switch W/Retard <br /> Maintenance <br /> Inspect detectors monthly. If leaks are found,replace the detector. The VSR waterflow switch should provide years of trouble-free service. The retard <br /> and switch assembly are easily field replaceable.In the unlikely event that either component does not perform properly,please order replacement retard <br /> switch assembly stock#1029030(see Fig.8).There is no maintenance required,only periodic testing and inspection. <br /> Retard/Switch Assembly Replacement (See Fig.8) <br /> 1. Make sure the fire alarm zone or circuit connected to the waterflow switch is bypassed or otherwise taken out of service. <br /> 2. Disconnect the power source for local bell(if applicable). <br /> 3. Identify and remove all wires from the waterflow switch. <br /> 4. Remove the(2)mounting screws holding retard/switch assembly to the base.Do not remove the(2)retard housing screws. <br /> 5. Remove the retard assembly by lifting it straight up over the tripstem. <br /> 6. Install the new retard assembly.Make sure the locating pins on the retard/switch assembly fit into the locating pin bosses on the base. <br /> 7. Re-install the(2)original mounting screws. <br /> 8. Reconnect all wires.Perform a flow test and place the system back in service. <br /> 1 <br /> The Retard/Switch Assembly is field-replaceable 7pipe <br /> g <br /> the system or removing the waterflow switch fro <br /> Fig.8 REMOVE(2)ORIGINAL MOUNTING <br /> SCREWS HOLDING RETARD/SWITCH <br /> ASSEMBLY TO BASE <br /> BREAK OUT THIN SECTION OF CO V ER <br /> WHEN WIRING BOTH SWITCHES <br /> FROM ONE CONDUIT ENTRANCE. (2)ORIGINAL MOUNTING <br /> CREWS <br /> RETARD/SWITCH ASSEMBLY <br /> Li <br /> (2)LOCATING PINS <br /> i <br /> o � � <br /> (2)LOCATING PINS <br /> DO NOT REMOVE BOSSES IN BASE <br /> (2)RETARD HOUSING <br /> SCREWS <br /> m <br /> BASE <br /> a <br /> 0 <br /> O O <br /> DWG#1146-10 <br /> Potter Electric Signal Company, LLC St. Louis, MO Phone: 800-325-3936 www.pottersignal.com <br /> 5401146-REV N 10/21 PAGE 4 OF 5 <br />
The URL can be used to link to this page
Your browser does not support the video tag.