1605 SE EVERETT MALL WAY WALMART 2025-09-10

TFP530 Page 6 of 8 eon Plate by under or over-tightening the sprinkler. Re-adjust the position of TO WET SIDE FACE OF the sprinkler fitting to suit. SYSTEM OUTLET SPRINKLER- PLUGGED FITTING Note:Install pendent sprinklers only in the pendent position. The Deflector of EXPOSURE a pendent sprinkler must be parallel to LENGTH the ceiling. Egan SPRINKLER (SEE DESIGN Step 1. With a non-hardening pipe- CRITERIA thread sealant such as TEFLON applied DSB-2 FITTING D8B-2 SECTION) to the Inlet threads, hand-tighten the BOOT (SEE DESIGN BOOT, sprinkler into the sprinkler fitting. Do CRITERIA not grasp the sprinkler by the Deflec- SECTION) tor, see Figure 7. Step 2. Wrench-tighten the sprinkler Jusing either: • a pipe wrench on the Inlet Band or the Casing, see Figure 1 FIGURE 8 FIGURE 10 • the W-Type 17 Sprinkler Wrench on SPRINKLER FITTING EXPOSURE LENGTH the Wrench Flat, see Figure 2 HEATED AREA Apply the Wrench Recess of the W-Type 17 Sprinkler Wrench to the STRAP TIES Wrench Flat. RUN (ENDS ON • OUTLET OPPOSING Note: If sprinkler removal becomes PLUGGED SIDES OF necessary, remove the sprinkler using BOOT) the same wrenching method noted SPRINKLER above.Sprinkler removal is easier when TO DRY FITTING DSB-2 BOOT a non-hardening sealant was used SYSTEM (SEE DESIGN ADHESIVE and torque guidelines were followed. CRITERIA After removal, inspect the sprinkler for SECTION) 2-3/4" DIA. damage. (69,9 mm) Step 3. After installing the ceiling and DSB-2 CLEARANCE applying a ceiling finish, slide on the BOOT HOLE outer piece of the escutcheon until INSULATED it comes in contact with the ceiling. FREEZER Do not lift the ceiling panel out of its STRUCTURE normal position. DS-2 When using the Deep Escutcheon, SHOWN hold the outer piece in contact with the WITH FLUSH mounting surface(ceiling or wall).Then ESCUTCHEON rotate the inner piece approximately 1/4 FIGURE 9 turn with respect to the outer piece, SPRINKLER FITTING FIGURE 11 to hold the Deep Escutcheon firmly UNHEATED AREA MODEL DSB-2 DRY SPRINKLER together. BOOT WITH SERIES DS-2 Installation DRY-TYPE PENDENT SPRINKLER Care a n d Do not install any bulb-type sprinkler Maintenance TYCO Series DS-2 Dry-Type Sprinklers, if the bulb is cracked or there is a loss 11.2K Pendent, Standard (5 mm bulb) of liquid from the bulb. With the sprin- TYCO Series DS-2 Dry-Type Sprin- and Quick Response(3 mm bulb), and kler held horizontally,a small air bubble klers, 11.2K Pendent, Standard (5 mm Standard Coverage must be installed in should be present.The diameter of the bulb)and Quick Response(3 Standard bulb), accordance with this section. air bubble is approximately 1/16 in. and Standard Coverage must be main- General Instructions (1,6 mm)for the 135 F (57 C) rating to tained and serviced in accordance with Series DS-2 Dry-Type Sprinklers must 1/8 in. (3,2 mm) for the 360°F (182°C) this section. only be installed in fittings that meet rating. the requirements of the Design Cri- A leak-tight 1 in. NPT sprinkler joint Before closing a fire protection system teria section. See the Design Criteria should be obtained by applying a min- main control valve for maintenance work on the fire protection system section for other important require- imum-to-maximum torque of 20 to ments regarding piping design and 30 lb-ft (26,8 to 40,2 N•m). Higher that it controls, obtain permission to sealing of the clearance space around levels of torque may distort the sprin- shut down the affected fire protection the sprinkler Casing. With reference kler Inlet with consequent leakage or systems from the proper authorities to Figure 7, do not grasp the sprinkler impairment of the sprinkler. and notify all personnel who may be by the Deflector. Failure to follow this affected by this action. instruction may impair performance of Do not attempt to compensate for nsufficient ad Absence of the outer piece of an the device. ijustment in an Escutch- escutcheon, which is used to cover a