Laserfiche WebLink
ELASTOSHIELDO TS G <br /> SBS (ELASTOMERIC) GRANULATED CAP SHEET <br /> APPLICATION INSTRUCTIONS MANUFACTURING FACILITIES <br /> Elastoshield TS G is intended to be used as the primary • Fernley, NV <br /> weathering surface in new or re-roof applications. Elastoshield • Hazleton, PA <br /> TS G is to be applied as the uppermost layer of a multi-ply roof • Waco, TX <br /> system applied over a compatible Polyglass base or interply • Winter Haven, FL <br /> membrane. Elastoshield TS G may be applied directly to certain <br /> non-combustible substrates. CORPORATE HEADQUARTERS <br /> • Apply over clean, dry, dust and debris-free substrates. Prime Polyglass U.S.A., Inc. <br /> concrete decks and required substrates prior to application with 1 1 1 1 West Newport Center Drive <br /> PG 100 Fast-Drying Asphalt Primer. Consult Polyglass Technical Deerfield Beach, FL 33442 <br /> Service if alternate primer is allowed. www.polyglass.us <br /> • When re-roofing, remove all prior roofing materials down to a General Line: (888)410-1375 <br /> clean debris-free substrate and properly close-off all abandoned (954) 233-1330 <br /> roof penetrations. Customer Service: 18001 222-9782 <br /> • Concrete or steel decks shall be designed with proper Technical Service: 18661 802-8017 <br /> expansion devices. Questions?technical@polyglass.com <br /> • Wood decks shall have all joints blocked and properly supported. Product Disclaimer: Unless otherwise incorporated into or part <br /> • Ensure the fire rating of the assembly over any combustible of a supplemental manufacturer's warranty, Polyglass warrants its <br /> substrate. product(s) against manufacturing defects in its product that directly <br /> • Ensure the installation of Elastoshield TS G does not prevent the results in leakage for a period of 5 years. <br /> ventilation of existing construction. <br /> • Do not apply over shingles or any granulated surface. Refer to safety data sheet(SDS) for specific data and handling of <br /> • While installing Elastoshield TS G: our products. All data furnished refers to standard production and <br /> is given in good faith within the applicable manufacturing and <br /> 1. Start at the low point of the roof. testing tolerances. <br /> 2. Unroll the material and allow to relax then re-roll the <br /> membrane once relaxed. Polyglass U.S.A., Inc., reserves the right to improve and change <br /> 3. Install in a solid mopping of Type III or Type IV asphalt, its products at any time without prior notice. Polyglass U.S.A., <br /> PG 350 Mod Bit Adhesive, or fully torch the burnoff film Inc. cannot be held responsible for the use of its products under <br /> creating a pool of asphalt. Pay close attention to the conditions beyond its own control. For most current product data <br /> sidelap. and warranty information, visit www.polyglass.us <br /> 4. Position successive rolls providing a minimum 6"end lap <br /> and 3"side lap. Asphalt bleed out shall be '/a" to 3/a" on all <br /> seams. <br /> 5. Matching loose granules may be sprinkled onto the bleed out. <br /> • Details and flashing may be installed using hot asphalt or <br /> cold application techniques. Check project details for proper <br /> installation requirements. <br /> • For detailed drawings and recommended installation <br /> procedures of typical roof segments, such as drip edge <br /> and T-joint conditions, please refer to our website at, <br /> www.polyglass.us <br /> ROOFING AND WATERPROOFING SYSTEMS <br /> MAPS/ <br /> Copyright©2020 by Polyglass U.S.A.,Inc.and all rights are reserved. www.Polyglass.us <br /> Edition Date:06/20•Doc#Elaateahield Ts G <br />