1001 N BROADWAY LEARNING RESOURCE CENTER 2026-01-15

2015 Washington State E. I Code Compliance Forms for Commercial,R2 and R3 over ories.and all R1-Page 8 of 17 'Mechanical Permit Plans Checklist MECH-CHKI 2015 Washington State Energy Code Compliance Forms for Commercial Buildings including R2&R3 over 3 stories and all R1 Revised January 2017 Project Title: Everett Community College-Learning Resource Center Date 7/24/2020 The following information is necessary to check a permit application for compliance with the mechanical systems and equipment requirements of the Washington State Energy Code,Commercial Provisions. Applicable TLocation in Building Department (yes,no,na) Code Section Code Provision Information Required-Mustbe in permit documents Documents Notes C402.4.1.4 Increased prescriptive Yes C403.6 maximum vertical Indicate that all occupied,conditioned spaces are served by a DOAS per C403.6 fenestmbon area with DOAS M3 Series Additional Efficiency Package Option,Dedicated Outside Air Systems(DOAS) Yes C406.6 Building provided wth To comply with additional efficiency package option,indicate that 901%or more of all occupied, DOAS conditioned s aces are served by a DOAS per 0403.6 M3 Series Multiple Zone Air Systems Air systems serving multiple Identify supply air systems serving multiple zones and the zones they serve on plans;indicate Yes C403.4.4 zones whether system is VAV and method of primary air control;or provide supporting documentation for applied exception to VAV M3 Series Provide equipment schedules on plans or MECH-EQ form that list all VAV air terminals and MO Series, types M3 Series VAV systems serving For each air terminal include:maximum airflow rates for primary supply air during zone peak Yes C403.4.4 multiple zones heating and zone peak cooling;maximum airflow during reheating,retooling or mixing; minimum airflow rate to maintain required ventilation,and the basis for these values;it IMC or ASHRAE 62.1 multiple zone equation is basis for minimum flow rates,provide calculation on MO Series, plans M3 Series Yes C403.4.4.1 Single duct VAV terminal Indicate single duct terminal units are configured to reduce primary supply air before reheating units or retooling Ml0 Series NA C403.4.4.2 Dual duct systems-terminal For systems with separate warm air and cool air ducts,indicate terminal units are configured to units reduce the flow from one dud to minimum before mixing with airfrom the other dud NA Indicate locations of dud static pressure sensors on plans;include at least one sensor per major dud branch;verify controller setpoint pressure at each sensor is<1.2 inch w.g. M10 Series C403.A.1_1 VAV system static Yes pressure sensors- For systems with zone level DDC,indicate controls are configured to monitor zone damper C403.4.1.2 sensors and DDC set points positions and reset static pressure setpoint based on the zone requiring most pressure; include control logic that automatically detects and generates an alarm if any zone excessively drives reset logic,and allows building operators to exclude zones from reset logic M10 Series Multiple-zone VAV system For systems with zone level DDC controls,indicate controls are configured to automatically Yes C403,4.4.3 ventilation optimization reduce outdoor airflow in response to changes in system ventilation efficiency;or exception controls taken M10 Series Yes C403.4.4.4 VAV system supply air reset Indicate controls automatically reset supply air temperature in response to building loads or outdoor air temperature;orexception taken M10Series Multiple Zone HVAC Systems,High Efficiency VAV-Required for systems utilizing C41)3.6 DOAS Exception 2,must comply with all 16 provisions C403.7, Indicate system is configured for 100%air economizer operation and complies with all related NA Item 1 Air economizer economizer requirements per C403.3(without economizer exceptions) NA C403.7, Provide DDC controls for all components of system;identify all DDC system input/output NA Item 2 Direct digital controls(DDC) control points;indicate capability for trending and graphical display NA For systems with minimum OSA>2,500 dm,indicate outdoor airflow monitoring station that NA C403.7, Outdoor airflow measures OSA intake under all load conditions;indicate control sequence that increases or Item 3 measurement and reduction reduces system OSA rim based on VAV terminal feedback of ventilation efficiency(per C403.4.4.3 without exceptions)or DCV(per C403.2.6.2) NA C403.7, For systems with minimum OSA>2,500 cfm,indicate supply airflow monitoring station NA Item 4 Supply airflow measurement capable of measuring supply air delivered to VAV terminals under all load conditions NA C403.7, Zone isolation and Verify maximum area served by a single HEVAV system is<_50,000 sf,or one entire floor, NA Item 5 maximum area served whichever is greater,in addition if a system serves>25,000 sf,that includes areas that are expected to be occupied non-simultaneously,indicate zone isolation controls per C403.2.4.4 NA C403.71 Interior/exterior zone Verify that VAV terminals serving interior cooling driven loads are sized per design supply air NA Item 6 design supply air temperature that is 5°F higher than VAV terminals serving exterior zones it temperature NA C403.7, Maximum air terminal inlet Identify air terminals with minimum primary airflow setpoints>50%of maximum setpoint in NA Item 7 velocity equipment schedule or MECH-EQ form;indicate airterminal inlet velocity does not exceed 900 fpm NA C403.7, Indicate DDC system sequences of operation are designed and configured per ASHRAE GPC NA Item 8 Sequence of operation 36 NA NA C403.7, Maximum aliowable system Verify fan system bhp is_<90%of the bhp limit per Option 2 equation in Table C403.2.11.1(1), Item 9 brake horsepower provide MECH-FANSYS forth for each system NA Indicate all series and parallel terminal fans have electronically commutated motors;indicate NA C403.71 Fan-powered terminal unit DDC control system is configured to vary air terminal fan speed as a function of the load; Item 10 motor and controt indicate fan speed during periods of low heating,low cooling,or ventilation only is<_66%of peak design air flow or provide supporting documentation for applied exception NA