Laserfiche WebLink
Seismic Bracing <br /> Fig. 828 - Universal Sway Brace Attachment to Steel ®TOLCO <br /> Size Range: One size accommodates all Fig. 900 Series sway brace <F M <br /> attachments. Fits from 3/8" (9.4mm)to 7/8"(22.2mm)thick steel structure. For APPROVED <br /> thicknesses less than 3/8"(9.4mm)refer to Fig. 825. <br /> Material: Steel Cone Point <br /> 4Gone <br /> Set Bolts A <br /> Function: To attach sway bracing to various types of steel structural members. <br /> Features: Permits secure non-friction connection without drilling or welding. Unique <br /> design allows offset placement on wide flange beam, I-beam, C-channel, open web, Set Bolts <br /> welded steel trusses, etc.. Secures brace to structure either across or along the Included <br /> beam. Break-off set bolts allow for visual verification of proper installation torque. <br /> Approvals: Factory Mutual Approved (FM).For UL Listed information refer to page 52. <br /> Installation Instructions: The Fig. 828 is the structural attachment Point Set <br /> component of a longitudinal or lateral sway brace assembly. It is intended Bolt B <br /> to be combined with a Cooper B-Line/TOLCO transitional attachment, "bracing pipe" <br /> and a Cooper B-Line/TOLCO "braced pipe" attachment to form a complete bracing <br /> assembly. NFPA 13 guidelines should be followed. <br /> To Install: Place the Fig. 828 on the flange of the beam,truss, or girder. Be sure the <br /> attachment is fully engaged to the rear of the opening.Tighten the cone point <br /> set bolts(A) until the heads break off.Tighten the cone point set bolt(B)until the <br /> head breaks off. Remove the flange nut from set bolt(B). Install a TOLCO swivel <br /> fitting Fig. 980 or any other Cooper B-Line/TOLCO approved transitional fitting). <br /> Use flange nut to secure the swivel fitting. <br /> Finish: Plain or Electro-Galvanized <br /> a <br /> Approx.Weight/100: 275 Lbs. (124.7kg) <br /> Order By: Figure number and finish ,r <br /> Patent#6,098,942 <br /> Canada Patent#2,286,659 <br /> Patent Pending <br /> Designed to meet or exceed requirements of FM DS 2-8. <br /> FM Approved Allowable Horizontal Load* <br /> With Brace Perpendicular To Beam <br /> Brace Angle(degrees from vertical) <br /> 30°-440 450-590 600-74' 75°-90° J ------------------------ <br /> 1570 2220 1210 700 Beam,truss,or Beam,truss,or girder <br /> (6.98kN) (9.87kN) (5.38kN) (3.11 kN) girder <br /> Fig.828 <br /> FM Approved Allowable Horizontal Load* �'` - FA <br /> ----- <br /> With Brace Parallel To Beam Fig.828 <br /> Brace Angle(degrees from vertical) Shown with <br /> May pivot in any <br /> o D D D D D D D Fig.980 direction <br /> 30 -44 45 -59 60 -74 75 -90 with <br /> r690 970 1210 1330 980 <br /> (3.07kN) (4.31 kN) (5.38kN) (5.91 kN) <br /> FM Approved design loads are based on ASD <br /> design method. <br /> Cooper B-Line, Inc.'s("Cooper B-Line")seismic bracing components are designed to be compatible only with other Cooper B-Line <br /> bracing components,resulting in a listed seismic bracing assembly. Cooper-B-Line's warranty for seismic bracing components will be <br /> the warranty provided in Cooper B-Line's standard terms and conditions of sale made available by Cooper B-Line,except that, in <br /> addition to the other exclusions from Cooper B-Line's warranty,Cooper B-line makes no warranty relating to Cooper B-Line's seismic <br /> bracing components that are combined with products not provided by Cooper B-Line. <br /> All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified. <br /> 00 <br /> COOPER B-Line <br />