Laserfiche WebLink
ODTOLCO" www.tolco.com <br /> 00: <br /> Fig. 980 - Universal Swivel Sway Brace Attachment C&USLtSTEO <br /> Size Range — One size fits bracing pipe 1" thru 2", TOLCO 12 gauge channel, and all <FM> <br /> structural steel up to 1/4" thick. <br /> Material — Carbon Steel Component of State of <br /> California OSHPD Approved <br /> Function — Multi-functional attachment to structure or Seismic Restraints System <br /> braced pipe fitting. <br /> Features — This product's design incorporates a concen- <br /> tric attachment opening which is critical to the performance H <br /> of structural seismic connections. NFPA 13 (2002) Figure <br /> 9.3.5.9.1 indicates clearly that fastener table load values are <br /> based only on concentric loading. Mounts to any surface <br /> angle. Break off bolt head assures verification of proper <br /> installation. <br /> Installation — The Fig.980 is the structural or transitional A <br /> attachment component of a longitudinal or lateral sway <br /> brace assembly. It is intended to be combined with the B <br /> "bracing pipe" and TOLCO "braced pipe" attachment, Fig. <br /> 1000, 1001, 2002, 4L, 4A or 4B to form a complete bracing <br /> assembly. NFPA 13 and/or OSHPD guidelines should be <br /> followed. <br /> To Install — Place the Fig. 980 onto the "bracing pipe". Tighten the set bolt until set bolt head breaks off. <br /> Attachment can pivot for adjustment to proper brace angle. <br /> Approvals — Underwriters Laboratories Listed in the USA(UL) and Canada (cUL). Approved by Factory Mutual <br /> Engineering (FM). Included in our Seismic Restraints Catalog approved by the State of California Office <br /> of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information <br /> relating to OSHPD projects, please refer to the TOLCO Seismic Restraint Systems Guidelines. <br /> Note — The Fig. 980 Swivel Attachment and the Fig. 1001, Fig. 1000 , Fig. 2001 or Fig. 4A Pipe Clamp make up a <br /> sway brace system of UL Listed attachments and bracing materials which satisfies the requirements of Underwriters' <br /> Laboratories and the National Fire Protection Association (NFPA) <br /> Finish — Plain <br /> Note — Available in Electro-Galvanized finish. R> <br /> Order By — Figure number and finish. --- <br /> PATENT #6,273,372, PATENT#6,517,030, PATENT#6,953,174, <br /> PATENT#6,708,930, PATENT #7,191,987, PATENT#7,441,730 <br /> Lateral Brace <br /> Dimensions •Weights <br /> Max. Design **Max. Design Approx. <br /> A B H* Load Lbs. Load Lbs. <br /> (cULus) (FM) Wt./100 <br /> 51/4 17/8 17/32 2765 2800 132 <br /> Available with hole sizes to accommodate up to 3/4"fastener. Consult factory. <br /> **Load shown is allowable with brace installed,between 30'-90°.No reduction of load based on <br /> brace angle is required. <br /> TOLCO°brand bracing components are desgined to be compatible ONLY with other TOLCO®brand bracing components, resulting in a Listed <br /> seismic bracing assembly. DISCLAIMER — NIBCO does NOT warrant against the failure of TOLCO°brand bracing components, in the instance <br /> that such TOLCO°brand bracing components are used in combination with products, parts or systems which are not manufactured or sold under <br /> the TOLCO°brand. NIBCO shall NOT be liable under any circumstance for any direct or indirect, incidental or consequential damages of any <br /> kind, including but not limited to loss of business or profit,where non-TOLCO brand bracing components have been,or are used. <br /> OFFICE/MANUFACTURING FACILITY•1375 SAMPSON AVE.•CORONA,CA 92879•PH- 951.737.5599•FAX- 951.737.0330 <br /> CUSTOMER SERVICE•800.786.5266 <br /> www,tolco.com <br />