2316 KENILWORTH PL 2025-12-01 - Laserfiche WebLink

GENERAL NOTES CONTRACTOR GROUNDING NOTES INTERCONNECTION NOTES BLOSSOM SOLAR SITE NOTES 2.5.1 GROUNDING SYSTEM COMPONENTS SHALL BE LISTED FOR 2.7.1 LOAD SIDE INTERCONNECTION SHALL BE IN 2.1.1 A LADDER WILL BE IN PLACE FOR INSPECTION IN ACCORDANCE THEIR PURPOSE, AND GROUNDING DEVICES EXPOSED TO THE ACCORDANCE WITH NEC 705.12. WITH OSHA REGULATIONS. ELEMENTS SHALL BE RATED FOR SUCH USE. 2.7.2 THE SUM OF THE UTILITY OCPD AND INVERTER 2.1.2 THE PV MODULES ARE CONSIDERED NON-COMBUSTIBLE AND THIS 2.5.2 PV EQUIPMENT SHALL BE GROUNDED IN ACCORDANCE CONTINUOUS OUTPUT MAY NOT EXCEED 120 PERCENT OF BLOSSOM SOLAR SYSTEM IS A UTILITY INTERACTIVE SYSTEM WITH NO STORAGE WITH NEC 690.43 AND NEC TABLE 250.122. BUSBAR RATING PER NEC 705.12. BATTERIES. 2.5.3 METAL PARTS OF MODULE FRAMES, MODULE RACKING, AND 2.7.3 THE SUM OF 125 PERCENT OF THE POWER SOURCE(S) 2.1.3 THE SOLAR PV INSTALLATION WILL NOT OBSTRUCT ANY ENCLOSURES CONSIDERED GROUNDED IN ACCORDANCE WITH OUTPUT CIRCUIT CURRENT AND THE RATING OF THE #3507 ARLINGTON,WA, 98223 PLUMBING, MECHANICAL, OR BUILDING ROOF VENTS. NEC 250.134 AND 250.136(A). OVERCURRENT DEVICE PROTECTING THE BUSBAR SHALL 2.1.4 PROPER ACCESS AND WORKING CLEARANCE AROUND EXISTING 2.5.4 EQUIPMENT GROUNDING CONDUCTORS SHALL BE SIZED IN NOT EXCEED 120 PERCENT OF THE AMPACITY OF THE LIC. NO. -0 AND PROPOSED ELECTRICAL EQUIPMENT WILL BE PROVIDED IN ACCORDANCE WITH NEC 690.45 AND INVERTER BUSBAR, PV DEDICATED BACKFEED BREAKERS MUST BE ACCORDANCE WITH SECTION NEC 110.26. MANUFACTURER'S INSTALLATION PRACTICES LOCATED OPPOSITE END OF THE BUS FROM THE UTILITY 2.1.5 ROOF COVERINGS SHALL BE DESIGNED, INSTALLED, AND 2.5.5 EACH MODULE WILL BE GROUNDED AS SHOWN IN SOURCE OCPD IN ACCORDANCE WITH NEC 705.12. MAINTAINED IN ACCORDANCE WITH THIS CODE AND THE APPROVED MANUFACTURER DOCUMENTATION AND APPROVED BY THE AHJ. 2.7.4 AT MULTIPLE ELECTRIC POWER SOURCES OUTPUT MANUFACTURER'S INSTRUCTIONS SUCH THAT THE ROOF COVERING 2.5.6 THE GROUNDING CONNECTION TO A MODULE SHALL BE COMBINER PANEL, TOTAL RATING OF ALL OVERCURRENT SERVES TO PROTECT THE BUILDING OR STRUCTURE. ARRANGED SUCH THAT THE REMOVAL OF A MODULE DOES NOT PROTECTION DEVICES SHALL NOT EXCEED AMPACITY OF INTERRUPT A GROUNDING CONDUCTOR TO ANOTHER MODULE. BUSBAR. HOWEVER, THE MAIN OVERCURRENT PROTECTION EQUIPMENT LOCATIONS 2.5.7 GROUNDING AND BONDING CONDUCTORS, IF INSULATED, DEVICE MAY BE EXCLUDED IN ACCORDANCE WITH NEC 2.2.1 ALL EQUIPMENT SHALL MEET MINIMUM SETBACKS IN SHALL BE COLORED GREEN OR MARKED GREEN IF#4 AWG OR 705.12. ACCORDANCE WITH NEC 110.26. LARGER PER NEC 250.119 2.7.5 FEEDER TAP INTERCONNECTION (LOAD SIDE) IN 2.2.2 WIRING SYSTEMS INSTALLED IN DIRECT SUNLIGHT MUST BE 2.5.8 THE GROUNDING ELECTRODE SYSTEM COMPLIES WITH NEC ACCORDANCE WITH NEC 705.12. RATED FOR EXPECTED OPERATING TEMPERATURE AS SPECIFIED BY 690.47 AND NEC 250.50 THROUGH 250.106. IF EXISTING SYSTEM IS 2.7.6 SUPPLY SIDE TAP INTERCONNECTION IN ACCORDANCE NEC 690.31 (A),(C)AND NEC TABLES 310.15 (13)(2)(A)AND 310.15 (B)(3)(C). INACCESSIBLE, OR INADEQUATE, A GROUNDING ELECTRODE WITH TO NEC 705.12 WITH SERVICE ENTRANCE 2.2.3 JUNCTION AND PULL BOXES PERMITTED INSTALLED UNDER PV SYSTEM PROVIDED IN ACCORDANCE WITH NEC 250, NEC 690.47 CONDUCTORS IN ACCORDANCE WITH NEC 230.42. PROJECT NAME &ADDRESS MODULES IN ACCORDANCE WITH NEC 690.34. AND THE AHJ. 2.7.7 BACKFEEDING BREAKER FOR ELECTRIC POWER 2.2.4 ALL EQUIPMENT SHALL BE INSTALLED ACCESSIBLE TO QUALIFIED 2.5.9 GROUND-FAULT DETECTION SHALL COMPLY WITH NEC SOURCES OUTPUT IS EXEMPT FROM ADDITIONAL PETER LABIB PERSONNEL IN ACCORDANCE WITH NEC APPLICABLE CODES. 690.41(B)(1)AND (2) TO REDUCE FIRE HAZARDS FASTENING PER NEC 705.12. 2316 KENILWORTH PL, 2.2.5 ALL COMPONENTS ARE LISTED FOR THEIR PURPOSE AND RATED EVERETT, WA, 98203 FOR OUTDOOR USAGE WHEN APPROPRIATE. DISCONNECTION AND OVERCURRENT PROTECTION NOTES APN #: 00734800001300 2.6.1 DISCONNECTING SWITCHES SHALL BE WIRED SUCH THAT AHJ: CITY OF EVERETT STRUCTURAL NOTES WHEN THE SWITCH IS OPENED THE CONDUCTORS REMAINING UTILITY: SNOHOMISH COUNTY 2.3.1 RACKING SYSTEM & PV ARRAY WILL BE INSTALLED IN ENERGIZED ARE CONNECTED TO THE TERMINALS MARKED "LINE PUD ACCORDANCE WITH THE CODE-COMPLIANT INSTALLATION MANUAL. SIDE" (TYPICALLY THE UPPER TERMINALS). TOP CLAMPS REQUIRE A DESIGNATED SPACE BETWEEN MODULES, AND 2.6.2 DISCONNECTS TO BE ACCESSIBLE TO QUALIFIED UTILITY SYSTEM DETAILS RAILS MUST ALSO EXTEND A MINIMUM DISTANCE BEYOND EITHER PERSONNEL, BE LOCKABLE, AND BE A VISIBLE-BREAK SWITCH DC SIZE:AC DC-(STC) AC SIZE:22.8000 KW AC EDGE OF THE ARRAY/SUBARRAY, IN ACCORDANCE WITH RAIL 2.6.3 PV SYSTEM CIRCUITS INSTALLED ON OR IN HABITABLE (48)SILFAB SOLAR SIL-440 QD(440W) MANUFACTURE (18)TESLAR'S INSTALLATION PRACTICES. BUILDINGS SHALL INCLUDE A RAPID SHUTDOWN FUNCTION TO ( 1588000-7.68)TESLA PV RAPID SHUTDOWN N MCI-2(1 PER 2.3.2 JUNCTION BOX WILL BE INSTALLED PER MANUFACTURER'S REDUCE SHOCK HAZARD FOR EMERGENCY RESPONDERS IN s MODULE) SPECIFICATIONS. IF ROOF-PENETRATING TYPE, IT SHALL BE FLASHED & ACCORDANCE WITH 690.12 SEALED PER LOCAL REQUIREMENTS. 2.6.4 ALL OCPD RATINGS AND TYPES SPECIFIED ACCORDING TO REVISIONS 2.3.3 ROOFTOP PENETRATIONS FOR PV RACEWAY WILL BE COMPLETED NEC 690.8, 690.9, AND 240. REV DESCRIPTION DATE AND SEALED W/APPROVED CHEMICAL SEALANT PER CODE BY A 2.6.5 INVERTER ON-GRID BRANCHES SHALL BE CONNECTED TO A LICENSED CONTRACTOR. SINGLE BREAKER OR GROUPED FUSE DISCONNECT(S) IN 2.3.4 ALL PV RELATED ROOF ATTACHMENTS TO BE SPACED NO ACCORDANCE WITH NEC 110.3(B). GREATER THAN THE SPAN DISTANCE SPECIFIED BY THE RACKING 2.6.6 IF REQUIRED BY THE AHJ, SYSTEM WILL INCLUDE MANUFACTURER OR PROFESSIONAL ENGINEERING GUIDANCE. ARC-FAULT CIRCUIT PROTECTION IN ACCORDANCE WITH NEC 2.3.5 WHEN POSSIBLE, ALL PV RELATED RACKING ATTACHMENTS WILL 690.11 AND UL1699B. BE STAGGERED AMONGST THE ROOF FRAMING MEMBERS. SHEET TITLE WIRING & CONDUIT NOTES NOTES 2.4.1 ALL CONDUIT AND WIRE WILL BE LISTED AND APPROVED FOR THEIR PURPOSE. CONDUIT AND WIRE SPECIFICATIONS ARE BASED ON MINIMUM CODE REQUIREMENTS AND ARE NOT MEANT TO LIMIT DRAWN DATE 4/11/2025 UP-SIZING. 2.4.2 CONDUCTORS SIZED IN ACCORDANCE WITH THE NEC DRAWN BY AN 2.4.3 AC CONDUCTORS TO BE COLORED OR MARKED PER NEC SHEET NUMBER 2.4.4 LISTED OR LABELED EQUIPMENT SHALL BE INSTALLED AND USED IN ACCORDANCE WITH ANY INSTRUCTIONS INCLUDED IN THE LISTING OR LABELING PER NEC PV-05