Laserfiche WebLink
Component Perform ,ce Path, pg. 1 Zo,. s 4c/5b ENV-UA <br /> 2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2&R3 over 3 stories and all R1 Revised Oct 2013 <br /> Project Address Underwood Gartland - Building A Date 05/18/2015 <br /> Occupancy Group @ Commercial C.) Group R For Building Department Use <br /> Change in occupancy or space conditioning 0 <br /> Note-Proposed UA may exceed Target UA by 10%per C101.4.4 and C101.4.5 <br /> Fenestration Area as%gross above-grade wall area 7.7% Max.Target: 30.0% <br /> Skylight Area as%gross roof area 1.3% Max.Target: 5.0% <br /> Vertical Fenestration Alternates: None Selected on ENV-SUM <br /> Notes: 1:If vertical fenestration or skylight area exceeds maximum allowed per C402.3.1, then Target Area Adjustment of all applicable envelope <br /> elements will be calculated by the compliance form. Refer to Target Area Adjustments worksheet for this calculation. <br /> 2:U-factors shall come from Appendix A,Chapter C303, or calculated per approved method as specified in C402.1.2. <br /> Building Component Proposed UA Target UA <br /> Provide source of U-factor,page/plan#of assembly detail&ID U-factor x Area(A) =UA(U x A; U-factor x Area(A)= UA(U x A) <br /> R.20.833 ID:Rigid Above Deck 0.048 198080 9507.8 0.034 198080 6734.7 <br /> o R= ID:(R-20 Insultaion Only Per Table 102.2.6) Above Deck Insulation U-0.034 <br /> R= ID: <br /> N -o R= ID: 0.031 <br /> o m R= ID: Metal Building U-0.031 <br /> R= ID: <br /> R= ID: 0.021 II <br /> Cr) R= ID: Single raft,attic,other U-0.021 <br /> R= ID: <br /> R= ID: i 0.055 1 <br /> LU R= ID: Steel/metal frame U-0.055 <br /> R= ID: <br /> o a R= ID: 0.052 1 <br /> m R= ID: Metal Building U-0.052 <br /> N R R= ID: <br /> 8 R= ID: 0.054 <br /> Eo R = ID: l Wood Frame,other U-0.054 <br /> a R= ID: 11 <br /> 0 <br /> in R=11 ID:w/Stick-pin Insulation R-11 (A103.3.7.1(2)) 0.081 59587 4826.5 0.104 59587 6197.0 <br /> 2 R= ID: Mass Wall U-0.104 <br /> R= ID: <br /> cn R= ID: 0.104 1 <br /> CO <br /> o R= ID: Assumed to be Mass Wall U-0.104 <br /> ac6) <br /> m 6R= I D: <br /> (.0 R= ID: <br /> N R= ID: 0.031 <br /> R= ID: Mass Floor U-0.031 <br /> o R= ID: <br /> o <br /> m R= ID: 0.029 <br /> E R= ID: Joist/Framing U-0.029 <br /> El <br /> u R= ID: <br /> F-factor x Perimeter =UA(U x A) F-factor x Perimeter= UA(U x A) <br /> 70 R. ID:No Insulation 0.730 2572 1877.6 0.540 2572 1388.9 <br /> E R= ID: <br /> � Slab-On-Grade U-0.54 <br /> D co c R= ID: <br /> o <br /> R= ID: I 0.550 <br /> �n ami R. ID: Heated Slab-On-Grade U-0.55 <br /> = R= ID: <br /> i <br /> *Proposed non-residential CMU walls meeting Table C402.1.2 Area UA Area UA <br /> Footnote D requirements can use the target U-value of 0.104 rather Page 1 <br /> than Appendix A values.Show footnote requirements in plans. Subtotal 2 6 0 2 3 9 16212 2 6 02 3 9 14321 <br /> Component Performance Compliance (UA) UA COMPLIES <br />