9930 EVERGREEN WAY PAROBA COLLEGE 2016-08-05

Mechanical Permit Plans Checklist - Page 3 of 3 MECH-CHK 2012 Washington State Energy Code Compliance Forms for Commercial,Group R1,and>3 story R2 and R3 Revised June 2013 Project Address 9930 Evergreen Way Date 11/25/2014 The following information is necessary to check a mechanical permit application for commercial provision compliance with the 2012 WSEC. NOTE:Define print area in Excel prior to printing MECH-CHK pages. Applicability Location on Building Department (yes,no,na) Code Section Code Provision Information Required Plans Notes COMPLEX SYSTEMS,CONTINUED Specific System Requirements NA C403.4.2& C403.2.12 Variable flow control-fans Indicate fans requiring variable flow control and method NA C403.4.2.1 VAV fan static pressure Indicate sensor locations on plans;include at least one sensor per major duct sensors branch C403.4.2.2 VAV fan static pressure Indicate fan system static pressure setpoint based on zone requiring most NA setpoint pressure C403.4.5 VAV systems serving multi- Indicate supply air systems serving multiple zones that are required to be NA zones VAV,method of primary air control,and zones served;note exceptions taken NA C403.4.5.4 VAV system supply air reset Indicate controls that automatically reset supply air temp in response to loads NA C403.4 Large capacity cooling Indicate method of multi-stage or variable control for building cooling system systems capacity>300 tons NA C403.4.7 Hot gas bypass limitation Indicate cooling equipment unloading or capacity modulation method NA C403.4.3 Large capacity boiler systems Indicate multi-stage or modulating burner for single boilers>500,000 btuh NA C403.4.3 Boiler sequencing Indicate automatic controls that sequence operation of multiple boilers C403.4.3.5 Chiller/boiler plant pump Indicate capability to automatically reduce overall plant flow and shut-off flow NAisolation through chillers&boilers when not in use C403.4.2& Variable flow control- NA C403.4.3.6 pumps Indicate pumps requiring variable flow control&method NA 04Variable flow control- &C403.4.4 cooling towers Indicate cooling tower fans requiring variable flow control and method & Hydronic system part load 11.1,-.11.G Ga u y IS la,, ..a,GI oyOLG11,1,IGIVG llwo Naum y, ate, a, a„y NA C403.4.3.4 controls reset supply water temp AND reduce flow by 2 50/for systems>300,000 NA C403.4.3.2 Two-pipe changeover Indicate deadband,heating/cooling mode scheduling and changeover systems temperature range NA C403.4.3.3.1 Water loop heat pump- Indicate capability of central equipment to provide min.20°F water supply deadband temp deadband between heat rejection and heat addition modes NA C403.4.3.3 Water loop heat pump-heat Provide heat exchanger that separates cooling tower and heat pump loop in rejection Climate Zone 5 NA C403.4.3.3.3 Water loop heat pump- Indicate 2-way isolation valve on each heat pump and variable flow control for isolation systems with total pump power>10 hp C403.4.6 recovery Condenser water heat Indicate system provided to pre-heat service water and efficiency NA NA C403.5 Cooler/freezer-anti-sweat Indicate w/sf&control method for walk-in cooler/freezer door anti-sweat heaters heaters NA C403.5/6 Cooler/freezer-evaporator Indicate motor type for evaporator and condenser fans<1 hp and condenser fans SERVICE WATER HEATING Service Water Systems NA C404.2 Water-heating equip min. Provide equipment schedule or complete MECH-SUM table with type, efficiency capacity,efficiency,test standard(or other efficiency source) NA C404.3 Temperature controls Indicate temperature controls have required setpoint capability NA C404.4 Heat traps Indicate piping connected to equipment have heat traps on supply& discharge NA C404.5 Insulation under water heater Indicate R-10 insulation under tank NA C404.6 Service water piping insulation Indicate R-value of insulation on piping;note exceptions taken C404.7/8 Circulation systems and heat Indicate shut-off capability based on occupancy and periods of limited NA trace shut-off demand NA C404.9 Group R-2 service hot water Indicate method of usage metering for dwell.units served by central HW meters system Pools&In-Ground Permanently Installed Spas Pool heating equip min. Provide equipment schedule or complete MECH-SUM table with type, NA C404.10.1 efficiency capacity,efficiency,test standard(or other eff.source);heat pump heaters z 4 COP NA C404.10.1/2 Pool heater on/off controls Indicate automatic on/off control based on scheduling&accessible on/off switch on heater that operates independent of thermostat setting;or NA C404.10.3 Pool covers Indicate vapor retardant cover and insulation rating as required NA C404.10.3 Pool assembly insulation Indicate rating of insulation on sides and bottom of pools heated to>90°F NA C404.10.4 Heat recovery Indicate method,exhaust air temperature reduction and recovered energy use