9930 EVERGREEN WAY PAROBA COLLEGE 2016-08-05

Mechanical Permit Plans Checklist - Page 2 of 3 MECH-CHK 2012 Washington State Energy Code Compliance Forms for Commercial,Group R1,and>3 story R2 and R3 Revised June 2013 Project Address 9930 Evergreen Way Date 11/25/2014 The following information is necessary to check a mechanical permit application for commercial provision compliance with the 2012 WSEC. NOTE:Define print area in Excel prior to printing MECH-CHK pages. Applicability Code Section Code Provision Information Required Location Building Department (yes,no,na) on Plans Notes GENERAL PROVISIONS,CONTINUED HVAC System Controls&Criteria,Continued NA C403.2.12 Variable flow control- Indicate fan&pump motors requiring VF control&method(VSD or equiv fans/pumps controls) VarNA C403.2.12.1 cooling towersflow control- Indicate cooling tower fans requiring variable flow control and method cooling C403.2.12.2 Large volume fan systems Indicate fan systems requiring airflow reduction based on heating and NA cooling demand;or exception taken C403.2.12.2 Single zone AC systems Indicate method of cooling demand-based fan control for sys.>110,000 NA btuh NA C403.2.4.10 DDC system capabilities Identify all DDC system input/output control points and indicate capability for trending and demand response setpoint adiustment Ducting Systems NA C403.2.7.1& Indicate all ductwork constructed and sealed per IMC,C402 leakage C403.2.7.3 Duct construction requirements and IBC vapor retarder requirements NA C403.2.7.3.1;Duct pressure classifications Identify location of low,medium and high pressure ductwork on plans C403.2.7.3.3 High pressure duct leakage Indicate high pressure duct leakage testing requirements on plans;provide NAtest test results to jurisdiction when completed NA C403.2.7.1/2 Duct insulation Indicate R-value of insulation on ductwork Piping Systems NA C403.2.8 Piping insulation Indicate R-value of insulation on piping NA C403.2.8.1 Piping insulation exposed to weather Indicate method of protection from damage/degredation SIMPLE SYSTEMS Qualifying Systems NA C403.3 Qualifying single zone Verify unitary or packaged equipment does not exceed capacity limits,does systems not have active humidifcation or simultaneous heating/cooling NA C403.3 Qualifying 2-pipe heating systems Verify 2-pipe heating-only system does not exceed capacity limits NA C403.3.2 Hydronic system controls Refer to Complex Systems Section C403.4.3 Simple System Economizers YES C403.3.1 Air economizer required Indicate cooling systems requiring economizer controls;note in equip MO.00 sched. YES C403.3.1.1.1 Air economizer capacity Indicate modulating OSA control capability up to 100%OSA,or exception MO.00 YES C403.3.1.1.3 Air economizer high limit controls Indicate high limit shut-off control method per Table C403.3.1.1.3(2) MO.00 YES C403.1.1.2 Integrated air economizer Indicate capability for partial air economizer operation for systems with operation" capacity>65,000 btuh MO.00 NA C403.3.1 Air economizer exceptions Indicate eligible exception(s)taken and provisions to comply with exceotion(s) COMPLEX SYSTEMS Complex System Economizers C403.4.1 Air economizer required Indicate cooling systems requiring economizer controls;note in equip NA sched. C403.4.1.4 Economizer heating system Verify control method of HVAC systems with economizers does not NA impact increase building heating energy usage during normal operation NA C403.4.1.3 Integrated economizer Indicate capability for partial economizer operation for air or water econo operation systems Moved Water economizer capacity Indicate water econo capable of 100%cooling capacity at 50°F db/45°F wb NA OSA C403.4.1.2 Water economizer Indicate precooling coils and heat exchangers do not exceed pressure drop NA maximum pressure drop limit NA C403.3.1 Air economizer exceptions Indicate eligible exception(s)taken and provisions to comply with exceptions)