1402 SE EVERETT MALL WAY BUFFALO WILD WINGS 2016-09-20

■ � � • • 2012 Washington State Energy Code Compliance Forms for Commercial, Group R1, and > 3 story R2 and R3 Revised June 2013 Project Address Everett Mall Date 3/3/2015 The following information is necessary to check a mechanical permit application for commercial provision compliance with the 2012 WSEC. NOTE: Define rint area in Excel rior to rintin MECH-CHK a es. Applicability Location on Building Department (yes,no,na) Code Section Code Provision Information Required Plans Notes GENERAL PROVISIONS, CONTINUED HVAC System Controls 8 Criteria, Continued NA C403.2.12 Variable flow control - Indicate fan & pump motors requiring VF control & method (VSD or equiv fans/ um s controls NA C4032.12.1 Variable flow control - Indicate cooling tower fans requiring variable flow control and method coolin towers NA C403.2.12.2 Large volume fan systems Indicate fan systems requiring airflow reduction based on heating and coolin demand; or exce tion taken C403.2.12.2 Single zone AC systems Indicate method of cooling demand-based fan control for sys. > 110,000 YES bt"n M 102 NA C4032.4.10 DDC system capabilities Identify all DDC system inpuVoutput control points and indicate capability Ducting Systems C4032.7.1 & Indicate all ductwork constructed and sealed per IMC, C402 leakage YE$ C403.2.7.3 Duct construction re uirements and IBC va or retarder re uirements SPEC YE$ 4032.7.3.1- Duct pressure classifications Identify location of low, medium and high pressure ductwork on plans M 100 C4032.7.3.3 High pressure duct leakage Indicate high pressure duct leakage testing requirements on plans; provide NA test test results to 'urisdiction when com leted YE$ C403.2.7.1 / Duct insulation Indicate R-value of insulation on ductwork SPEC Piping Systems NA C403.2.8 Piping insulation Indicate R-value of insulation on piping NA C403.2.8.1 Piping insulation exposed to Indicate method of protection from damage/degredation weather 51MPLE SYSTEMS Qualifying Systems C403.3 Qualifying single zone Verify unitary or packaged equipment does not exceed capacity limits, does YE$ s stems not have active humidifcation or simultaneous heatin /coolin M 102 NA C403.3 Qualifying 2-pipe heating Verify 2-pipe heating-only system does not exceed capacity limits s stems NA C403.3.2 Hydronic system controls Refer to Complex Systems Section C403.4.3 Simple System Economizers YES C403.3.1 Air economizer required Indicate cooling systems requiring economizer controls; note in equip M 102 sched. YE$ C403.3.1.1.1 Air economizer capacity Indicate modulating OSA control capability up to 100% OSA, or exception M 102 YE$ C403.3.�.1.3 Air economizer high limit Indicate high limit shut-off control method per Table C403.3.1.1.3(2) M 102 controls YE$ C403.1.1.2 Integrated air economizer Indicate capability for partial air economizer operation for systems with M 102 o eration ca aci > 65 000 btuh NA C403.3.1 Air economizer exceptions Indicate eligible exception(s) taken and provisions to comply with COMPLEX SYSTEMS Complex System Economizers C403.4.1 Air economizer required Indicate cooling systems requiring economizer controls; note in equip NA sched. C403.4.1.4 Economizer heating system Verify control method of HVAC systems with economizers does not NA impact increase building heating energy usage during normal operation NA C403.4.1.3 Integrated economizer Indicate capability for partial economizer operation for air or water econo o eration s stems Moved Water economizer capacity Indicate water econo capable of 100% cooling capacity at 50°F db/45°F wb NA os,a C403.4.1.2 Water economizer maximum Indicate precooling coils and heat exchangers do not exceed pressure drop NA pressure drop limit NA C403.3.1 Air economizer exceptions Indicate eligible exception(s) taken and provisions to comply with