1402 SE EVERETT MALL WAY BUFFALO WILD WINGS 2016-09-20

■ ■ � � • 2012 Washington State Energy Code Compliance Forms for Commercial, Group R1, and > 3 story R2 and R3 Revised June 2013 ProjectAddress EverettMall Date 3/3/2015 The following information is necessary to check a mechanical pertnit application for commercial provision compliance with the 2012 WSEC. NOTE: Define rintarea in Excel riorto rintin MECH-CHK a es. Applicability Location on Building Department (yes,no,na) Code Section Code Provision Information Required Plans Notes COMPLEX SYSTEMS, CONTINUED Specific System Requirements C403.4.2 & Variable flow control - fans Indicate fans requiring variable flow control and method C403.2.12 C403.4.2.1 VAV fan static pressure Indicate sensor locations on plans; include at least one sensor per major sensors ductbranch C403.4.2.2 VAV fan static pressure Indicate fan system static pressure setpoint based on zone requiring most set oint ressure VAV systems serving multi- �ndicate supply air systems serving multiple zones that are required to be C403.4.5 VAV, method of primary air control, and zones served; note exceptions zones taken C403.4.5.4 VAV system supply air reset Indicate controls that automatically reset supply air temp in response to loads C403.4 Large capacity cooling Indicate method of multi-stage or variable control for building cooling s stems s stem ca aci > 300 tons C403.4.7 Hot gas bypass limitation Indicate cooling equipment unloading or capacity modulation method C403.4.3 Large capacity boiler Indicate multi-stage or modulating bumer for single boilers > 500,000 btuh s stems C403.4.3 Boiler sequencing Indicate automatic controls that sequence operation of multiple boilers C403.4.3.5 Chiller / boiler plant pump Indicate capability to automatically reduce overall plant flow and shut-off isolation flow through chillers & boilers when not in use C403.4.2 8 Variable flow control - �ndicate pumps requiring variable flow control & method C403.4.3.6 pumps C4032.12.1 Variable flow control - Indicate cooling tower fans requiring variable flow control and method & C403.4.4 coolin towers C403.4.3.4 Hydronic system part load reset supply water temp AND reduce flow by z 50% for systems > 300,000 controls C403.4.3.2 Two-pipe changeover Indicate deadband, heating/cooling mode scheduling and changeover s stems tem erature ran e C403.4.3.3.1 Water loop heat pump - Indicate capability of central equipment to provide min. 20°F water suppiy deadband tem deadband between heat re'ection and heat addition modes C403.4.3.3 Water loop heat pump - Provide heat exchanger that separates cooling tower and heat pump loop in heat re'ection Climate Zone 5 Water loop heat pump - Indicate 2-way isolation valve on each heat pump and variable flow control C403.4.3.3.3 isolation for s stems with total um ower > 10 h C403.4.6 Condenser water heat Indicate system provided to pre-heat service water and effciency recovery C403.5 Cooler / freezer - anti-sweat Indicate w/sf & control method for walk-in coolerlfreezer door anti-sweat heaters heaters C403.5 / 6 Cooler / freezer - evaporator Indicate motor type for evaporator and condenser fans < 1 hp SERVICE WATER HEATING Service Water Systems �� 2 Water-heating equip min. Provide equipment schedule or complete MECH-SUM table with type, efficienc ca aci efficienc test standard or other efficienc source C404.3 Temperature controls Indicate temperature controls have required setpoint capability C404.4 Heat traps Indicate piping connected to equipment have heat traps on supply & dischar e C404.5 �nsulation under water Indicate R-10 insulation under tank heater C404.6 Service water piping Indicate R-value of insulation on piping; note exceptions taken insulation C404.7 ! 8 Circulation systems and Indicate shut-off capability based on occupancy and periods of limited heat trace shut-off demand C404.9 Group R-2 service hot water Indicate method of usage metering for dwell. units served by central HW Pools & In-Ground Pertnanently Installed Spas Pool heating equip min. Provide equipment schedule or complete MECH-SUM table with type, C404.10.1 efficiency �Pacity, efficiency, test standard (or other eff. source); heat pump heaters 2 4 COP C404.10.1 / 2 Pool heater on / off controls Indicate automatic on/off control based on scheduling 8 accessible onloff switch on heater that o erates inde endent of thermostat settin � or C404.10.3 Pool covers Indicate vapor retardant cover and insulation rating as required C404.10.3 Pool assembly insulation Indicate rating of insulation on sides and bottom of pools heated to > 90°F C404.10.4 Heat recovery Indicate method, exhaust air temperature reduction and recovered energy