1402 SE EVERETT MALL WAY BUFFALO WILD WINGS 2016-09-20

� � • � ' � • • 2012 Washington State Energy Code Compliance rorms for Commercial Buildings including R2 & R3 over 3 stories and all R1 ProjectAddress Everett Mall Date 3/3/2015 The following information is necessary to check a building permit application for compliance with the building envelope requirements in the Washington State Energy Code, Commercial Provisions. Applicability Code Location in Building (yes,no,na) Section Component Compliance information required in permit documents Documents Department Notes SCOPE C101.52 Low energy spaces Low energy spaces identified on plans C101.5.21 Semi-heated spaces Semi-heated spaces identified on plans �4 �� ^�Sf�/,ti� C402.1.4 C402.5 Cooler and freezer Walk-in and refrigerated warehouse cooler and freezer spaces iden '' ! � C402.6 spaces plans C101.4.6 Mixed occupancy Spaces with different occupancy requirements identified on plan '� C101.4.4 Change of Existing F, S and U-occupancy building spaces undergoing a cha e C101.4.5 occupancy/space occupancy or space conditioning that require compliance are identi ied on � 0036789 conditioning plans �/ , �'C' l��'� � ENVELOPE PROVISIONS �'5��n'�� -� C303.1 Insulation Indicate identification mark shall be applied to all insulation materials identification C303.1.3 Fenestration product Fenestration products shall be labeled with rated U-factor, SHGC, VT, and C402.4.3 rating leakage rating Indicate installation methods, thicknesses, densities and clearances to C303.1.1 General insulation achieve the intended R-value of all insulation materials; C402.2 installation Where two or more layers of rigid insulation will be used, indicate that edge joints between layers are staggered Indicate R-value(s) of cavity/continuous insulation on roof sections; Indicate framing materials on roof sections; Indicate method of framing for ceilings below vented attics and vaulted C402.2.1 Roof assembly ceilings per A102.2 (std, adv); insulation provide area-weighted calculations for sloped insulation installed entirely above deck; Indicate R-values for thermal spacers and each insulation layer, and liner system (LS) method for metal building roofs C4022.1 Skylight curb Indicate curb insulation R-value on roof section if not included in skylight insulation NFRC rating Indicate R-value(s) of cavity/continuous insulation on wall sections; Indicate framing materials on wall sections; C4022.3 Indicate method of framing for wood const per A103.2 (std, int, adv); _ C402.2.4 Above/below grade Indicate mass of masonry walls; C303.2.1 Wall insulation Indicate loose-fill core insulation material, percentage of cores filled, and frequency of grouted cores and bond beams for masonry walls; Indicate method of protection of exposed exterior basemenUcrawlspace wall insulation Walk-in/refrigerated Indicate insulation R-values of ceilings, walls, doors, floors on sections; C402.5 warehouse cooler - C402.6 and freezer Indicate method of minimizing door infiltration; _ _ insulation Indicate type(s) of transparent doors and windows C4022.7 Opaque doors Indicate rated U-factor (swinging) or R-value (roll-up/sliding) on wall sections - applies to doors with less than 50 /o glazed area Floor over outdoor or Indicate R-value(s) of cavity/continuous insulation on floor sections; C402.2.5 unconditioned space Indicate framing material on floor sections; insulation Indicate mass of masonry floors Indicate R-value of continuous insulation on wall section or foundation detail; C402.2.6 Slab-on-grade floor Indicate insulation extends down vertically andlor horizontally the required C303.2.1 insulation distance from top of slab; Indicate method of protection of exposed exterior slab edge insulation Indicate R-value of continuous insulation on wall section or foundation detail; C402.2.6 Radiantly heated Indicate insulation extends down vertically from top of slab and then C303.2.1 slab-on-grade floor horizontally under the entire slab; insulation – --- - — Indicate method of protection of exposed exterior slab edge insulation Radiant heating Indicate insulation R-value behind radiant panels, U-bend/headers and C402.2.8 system insulation bottom surtace of radiantly heated floors (other than radiantly heated slab-on- grade)