3305 NASSAU ST WA CENTER FOR PAIN MANAGEMENT 2016-10-04

, ._ . . • � 2012 Washington State Energy Code Compliance Forms for Commercial, Group R1, and > 3 story R2 and R3 Revised ,lune 20�3 Project Address 3305 Nassau St. Date 2/12/2014 The following information is necessary to check a mechanical permit application for commercial provision compliance with the 2012 WSEC. NOTE: Define rint area in Excel rior to rintin MECH-CHK a es. Applicability Code Section Code Provision Information Required Location 8uilding Department (yes,no,na) on Plans Notes GENERAL PROVISIONS, CONTINUED HVAC System Controls & Criteria, Continued C403.2.12 Variable flow control - Indicate fan & pump motors requiring VF control & method (VSD or equiv N/A fans/ um s controls C4032.12.1 Variable flow control - Indicate cooling tower fans requiring variable flow control and method N/A coolinc towers C403.2.12.2 Large volume fan systems Indicate fan systems requiring airflow reduction based on heating and N/A coolin demand; or exce tion taken C403.2.12.2 Single zone AC systems Indicate method of cooling demand-based fan control for sys. > 110,000 N/A btuh N A C403.2.4.10 DDC system capabilities Identify all DDC system inpuUoutput control points and indicate capability � frrnin m m� r n im m� Ducting Systems C4032.7.1 & Indicate all ductwork constructed and sealed per IMC, C402 leakage M 1 YeS C403.2.7.3 Duct construction re uirements and IBC va or retarder re uirements 403.2.7.3.1- Duct pressure Identify location of low, medium and high pressure ductwork on plans N/A classifications C403.2.7.3.3 High pressure duct leakage Indicate high pressure duct leakage testing requirements on plans; provide N�A test test results to "urisdiction when com leted Ye5 C403.2.7.1 / Duct insulation Indicate R-value of insulation on ductwork M1 Piping Systems N/A C403.2.8 Piping insulation Indicate R-value of insulation on piping N/A C4032.8.1 Piping insulation exposed to Indicate method of protection from damage/degredation weather SIMPLE SYSTEMS Qualifying Systems C403.3 Qualifying single zone Verify unitary or packaged equipment does not exceed capacity limits, M1 Ye5 s stems does not have active humidifcation or simultaneous heatin /coolin N/A C403.3 Qualifying 2-pipe heating Verify 2-pipe heating-only system does not exceed capacity limits s stems N/A C403.3.2 Hydronic system controls Refer to Complex Systems Section C403.4.3 Simple System Economizers Indicate cooling systems requiring economizer controls; note in equip YeS C403.3.1 Air economizer required sched. M 1 Ye5 C403.3.1.1.1 Air economizer capacity Indicate modulating OSA control capability up to 100 % OSA, or exception M 1 C403.3.1.1.3 Air economizer high limit Indicate high limit shut-off control method per Table C403.3.1.1.3(2) M 1 Ye5 controls C403.1.1.2 Integrated air economizer Indicate capability for partial air economizer operation for systems with M 1 Y25 o eration ca aci > 65 000 btuh Indicate eligible exception(s) taken and provisions to comply with Ye5 C403.3.1 Air economizer exceptions M 1 xce i n COMPLEX SYSTEMS Complex System Economizers C403.4.1 Air economizer required Indicate cooling systems requiring economizer controls; note in equip M 1 Yes sched. C403.4.1.4 Economizer heating system Verify control method of HVAC systems with economizers does not Y2S impact increase building heating energy usage during normal operation M 1 C403.4.1.3 Integrated economizer Indicate capability for partial economizer operation for air or water econo M 1 Y25 o eration s stems Moved Water economizer capacity Indicate water econo capable of 100 % cooling capacity at 50°F db/45°F wb N/A osa, C403.4.1.2 Water economizer Indicate precooling coils and heat exchangers do not exceed pressure N/A maximum pressure drop drop limit N/A C403.3.1 Air economizer exceptions Indicate eligible exception(s) taken and provisions to comply with x in