Laserfiche WebLink
s <br /> ®� <br /> NOTES: (UNLESS OTHERWISE SPECIFIED) <br /> 1. ALL CONDUIT RUNS INCLUDE INSULATED BUSHINGS AND PULL STRINGS. <br /> 2. CONDUIT RUNS CANNOT EXCEED 50'FROM END-TO-END. DO NOT EXCEED FOUR(4)90 DEGREE BENDS. ao <br /> 3. CABLES BETWEEN ITEMS OVER 50 FEET IN LENGTH ARE PROVIDED BY THE CUSTOMER/CONTRACTOR. PLEASE <br /> REFER TO EQUIPMENT LIST FOR CABLE SPECIFICATIONS. <br /> 4. THE PRE-INSTALL MANUAL REQUIREMENTS SUPERSEDE ALL PRE-INSTALL NOTES IN THIS DRAWING PACKAGE.. <br /> J SWITCHPOINT INFINITY 3 P WALL MOUNTED 55" LCD MONITOR W <br /> DIMENSIONS: CONDUIT:ONE (1) 1 ' " CONDUIT �� <br /> /4 <br /> mm <br /> - MEDIA ROUTER: 20.6"W X 24"H X 17"D BACK BOX: ONE (1) 4"W X 4"H JUNCTION BOX WITH SINGLE-GANG MUD RING <X o <br /> - CONTROL SECTION: 12.5"W X 2.6"H X 17"D - MOUNTED DIRECTLY ABOVE THE TOP OF THE MOUNTING BRACKET. <�a <br /> - TOTAL SPACE REQUIRED: 27.5"W X 31"H X 29"D POWER: ONE (1) STANDARD DUPLEX OUTLET MOUNTED ADJACENT TO JUNCTION BOX. w ^o <br /> DATA: ONE (]) ETHERNET CONNECTION STRUCTURAL: CUSTOMER/CONTRACTOR TO MOUNT STRYKER PROVIDED BRACKET TO ° <br /> BACKBOX: ONE (i) 18"W X 18"H X 4"D (OR LARGER) JUNCTION BOX FLUSH MOUNTED. g z <br /> THE WALL IN THE DESIRED LOCATION WITH PROPER REINFORCEMENT TO SUPPORT THE w z a <br /> - SET BOTTOM OF BOX 9" ABOVE FINISHED FLOOR. MONITOR PRIOR TO STRYKER INSTALLATION. a0°LL <br /> NOTE:TERMINATE ALL INTEGRATION CONDUITS TO THIS JUNCTION BOX. DIMENSIONS:51.9"x 30.5"x 4.7" <br /> K VISUM LED POWER SUPPLY BOX <br /> NOTE:STRYKER PROJECT MANAGER WILL PROVIDE MOUNTING SPECIFICATIONS. Y <br /> DIMENSIONS: 12.5"W X 7"H X 15.5"D R WALL MOUNTED PAN/TILT/ZOOM CAMERA ! o w o <br /> - TOTAL SPACE REQUIRED: 20"W X 9"H X 21"D CONDUIT:ONE (1) 1" CONDUIT <br /> DATA: ONE (1) ETHERNET CONNECTION WHEN THERE IS NOT A SPI-3 IS PRESENT BACK BOX: ONE (1) 4"W X 4"H JUNCTION BOX WITH DUAL-GANG MUD RING <br /> BACKBOX: ONE (1) 6"W X 6"H X 4"D (OR LARGER) JUNCTION BOX FLUSH MOUNTED. - FLUSH MOUNTED IN WALL 12" BELOW FINISHED CEILING Qo <br /> w <br /> - SET BOTTOM OF BOX 14' ABOVE FINISHED FLOOR. POWER: NONE < = <br /> NOTE:TERMINATE ALL SURGICAL LIGHT CONDUITS TO THIS JUNCTION BOX o z W <br /> °W <br /> 0 Q m <br /> �. I.. OC � � � w <br /> L VISUM LIGHT AND CAMERA WALL CONTROL PANEL <br /> CONDUIT: ONE (1) 3/<" CONDUIT TO LIGHT POWER SUPPLY BOX. N E Q z o <br /> BACK BOX: ONE (1) RACO 942, 3-GANG JUNCTION BOX. <br /> _j 0 <br /> VWDo, RZ <br /> - MOUNT IN VERTICAL ORIENTATION AT CONVENTIONAL LIGHT SWITCH HEIGHT. Ln 0 Z 0 y <br /> - IF MULTIPLE WALL CONTROL PANELS ARE INSTALLED, A MINIMUM OF 1.5" IS c o zz z <br /> REQUIRED BETWEEN EACH RACO 942 JUNCTION BOX. ; O W o O <br /> Fn <br /> POWER: NONE ? < o <br /> ZCe 0 ° <br /> M BRACKET MOUNTED WALL SPEAKER w g <br /> CONDUIT: ONE (1) 3/ CONDUIT Lu o w o <br /> BACK BOX: ONE (1) 4"W X 4"H JUNCTION BOX WITH SINGLE-GANG MUD RING o o w o <br /> - MOUNT THE J-BOX IN WALL AT 12" BELOW FINISHED CEILING OR AS REQUESTED 0 V O O <br /> NI WALL PLATE I SINGLE GANG I COPPER DVI <br /> CONDUIT:ONE (1) 11/2" CONDUIT <br /> BACK BOX:ONE (1) 4"W X 4"H JUNCTION BOX WITH SINGLE-GANG MUD RING <br /> - MOUNT THE J-BOX 18" ABOVE FINISHED FLOOR. <br /> POWER: NONE REQUIRED, BUT SHOULD BE LOCATED NEXT TO OUTLET. > <br /> w <br /> N2 WALL PLATE I SINGLE GANG I VGA/S-VIDEO/BNC w N U <br /> CONDUIT:ONE (1) 1" CONDUIT F— ---i <br /> BACK BOX:ONE (1) 4"W X 4"H JUNCTION BOX WITH SINGLE-GANG MUD RING O O U <br /> - MOUNT THE J-BOX 18" ABOVE FINISHED FLOOR. <br /> POWER: NONE REQUIRED, BUT SHOULD BE LOCATED NEXT TO OUTLET o g <br /> Z J <br /> Q <br /> Z < 0 <br /> Lu OL w <br /> CIL, O Lu <br /> W <br /> OL U <br /> Lu <br /> 0 <br /> � <br /> w <br /> Ow <br /> REP:JEFF ELDEREGE <br /> PN DENNIS MARSHAL <br /> SHE"T' <br /> ALITOCAD DRAWING TEMPLATE I TEM I OOXX I REV.A PN (2) <br /> PLOT STAMP:MONTGOMERY,ERIC I DATE:11/30/2015 2:07 PM"01 <br /> f <br />