Laserfiche WebLink
COMPLIANCE <br />REVIRED <br />■n <br />01 <br />no <br />IN7�j <br />AIMPORTANT: Please supply Information In the shaded boxes and check the appropriate <br />circles. Disregard topics that don't describe your building or equipment. <br />checks In the two left columns. DO NOT place <br />e <br />❑lab Insulation, it not located on the Inferior, shall be R-10 (Table 6.2). <br />❑lab Insulation, rl present, shall approved for below grade use and protected above grade. <br />❑luding rim joists, shall be insulated without compression to (Table 6 2) <br />all (Options t,li) OR-19 (Option III, N; V. Vl, Vil) <br />Cj Qlnterlorbelow grade walls shall be Insulated without compression to OR-15 (Options I, IO �, 19 P (Table 6 2) <br />❑ QVaulted ceilings shall be Insufaated without com etsston tohR 30 (Table 6 2, All options) <br />❑ Qi Skylight wall Insulation is Installed and equivalent to the required wall R-values above. <br />❑ Q Vapor relarders h l <br />5 ■ <br />C <br />s a I be Installed toward the warm surface as represented below (502.1.6): , <br />Seleot one option for floors,walfs, and.approprlate ceilings <br />Floors: Plywood W/exterior lug . <br />Walls: Poty plastic (z 4 Mtl g PoIY (z 4 Mil) JgBacked baps <br />t Face -stapled, backed bathe 0 PVA;pelnt , <br />Ceilings: otrequired where Ventilatlon space averages >122 above insulation. Face stapled backed bafts QPoly plastic (a 4 m1) PVA aint <br />O p <br />3 Healing system efficiency and sizing requirements shall be met as represented below <br />Heat Pump efficiency shall be met under the following compliance path{S.503.4j: 0 SPIN system, air source heat pump: HSPF2 6.8, Cop > nc : - <br />0`Single padeago, air source heat pump: HSPF a 6.6, COP> 3.0 - <br />Q Water source heat pump: Cop:. 3 8 <br />0 Ground source heat pump COP z 3.0QD <br />Central force-alr furnace AFUE rating, as listed in the GAMA Directory, shall be �StA.78 (Options 1;11, IV, VI, Vlq 0 > .88 (Option Ilq) Ox24 (Option V) <br />s Nomcentral combustion heating systems shall have intermhe ignition <br />a� Maximum heating system output (150%of design heat load) IaZLMZ g7Ufir. (S.5D3.2.2 <br />ae High efficiency forced-alr furnace (s 56,000 BTU/hr; oulpugmay may exceed 1500/oof DHL <br />because: OGAMA listed AFUE is> 78 + i per each 5000 BTU/hroutput that it exceeds the DHC.. <br />WSEC Insulation phase requirements: <br />Inspected by: <br />Date_ <br />FINAL PHASE <br />❑ envelope Floors shall„be Insulated withroutcompressbn, and with rtsupport s'!20 O.0 to:- QR79 (Options I II, III, M V) , W25 (Ogoris Vf, Vit) <br />❑ e Non- v ul <br />9ttic callings shall be Insulated without compression to <br />1` -30 fOptlons 1;71, III, IV, V, Viq Q R38 (Option Yq See Table 6.2 <br />❑ QDoor systems shall lneet:r�U.40 (Ali options) <br />Door types are ( tit (2) (3) <br />tAlGiz� t=tGURE� IAA <br />Page 5 of 6 <br />