Laserfiche WebLink
H H <br />id H b •-'a i•' ;'^x ., A"x .A.� a,� s>. o: I' Fx•e `+ k i.+,' x »6�Y'FP <br />PO <br />t[H¢E y I JOM PLIANCE <br />y Iby H t' REOUIRED <br />ro m H I INSPECTION IMPORTANT: Please supply Information In the shaded coxes and check the appropriate <br />o APPROVED <br />•3 circles. Disregard topics that don't describe your building or equipment. QQ NO.I place <br />o H checks In the two left columns. <br />H ra <br />cr <br />N <br />yq y O �r <br />y I� �Biih <br />N <br />o toG- ©Exterior slab Insulation, if not located on the interior, shall be R-10 (Table 6-1) <br />JoExterior slab insulation material, H present, shall be approved for below grade use. <br />N <br />comcressionto;.(Table¢-1);-- <br />❑ ❑ 29 lntertor bPIow grade w-ans snau Uo-,n,o�w,�...,� �-•.- -..,. . <br />I 0R-21 (options 1, III,V VI,Vfi,Vili) Q R-19 (OpCtons II, IV) <br />o Vaulted ceilings shall be insulated without compression to (Table 6-1) R 30 (Ali options) <br />r Skylight wall Insulation is installed and equivalent to the required wall R-values above. <br />17 z -Vapor retarders shall be Installed toward the warm sunace as represented below (502.1.6) <br />Select one option for floors, walls, and appropriate ceilings: <br />4 Mil backed hafts <br />Floors: Q Plywood Wl exterior giva (D Poly (t pe dint <br />Walls: Poly plastic (2 A b1ii) a Face -stapled, backed batts PVA P <br />Ceilings: Not Not required where. ventilation space averages �12",above insulation. <br />T� 0Face stapled backed batts 0 Poly plastic (a 4 rl} � PVA paint <br />I I <br />-C] 3 Heating system efficiency and sizing requirements shall be met as represented below: <br />-� I ❑ _ ©Maximum heating system output (150% of d9sign heat load} Is KW {S. 503.2.2J`ks �: <br />©s Heating system requirements will is met with the following system (S.5D3.4.1.1): <br />Mir._ Model = Max. output KW <br />Type EYlSfi (l� <br />W'SI^C Insulation tease regkirements: <br />/ram Date-"'_ <br />inspected by - <br />di`I Envelope Floors shall be insulated without compression, and with support s 24' O.C. to R-30 Al <br />Options,'rabie 6-1). 6 1 <br />� Non -vaulted, attic ceilings shall be insuia ed without compression to R-33 (All Opbin, Table) <br />p Door systems shall meet: Q [3 a0 (Op•lons 1, lll} U °C (Cpt o.^s tl, IV V, VI, Vit, Vlil, Table o 1} <br />( Door types are (1) ;2) (3}� 7 - <br />❑ I e Exposed foam Insulation shall comply as follows (S. 5021 16). ' <br />❑ Protected with metal or plastic flashing or equivalent material that extends below grade. <br />Page 5 of 6 <br />