Laserfiche WebLink
_Address or Site ID: <br />1997WSEC''Resrdenti9CIttec is : <br />FRAMING <br />0 <br />0 <br />0 <br />0 <br />0 <br />m uance xe urrea ✓ <br />Ins 'on Approved ✓ <br />0 <br />6. All structural panels such as plywood, oriented strand board, particle board, and wafer board <br />shall be labeled "EXPOSURE I", "EXTERIOR", OR HUD-APPROVED"(VIAQ, S. 401.1). <br />0 <br />7. Insulation baffles shall be placed in attics/ceilings to maintain at least 1" ventilation space and <br />extend at least 6" vertically above batts or 12" vertically above loosefill insulation 5.502.1.4.5 . <br />0 <br />8. Glazing efficiency / Maximum allowed glazing area Shall be as calculated on Glazing Schedule <br />and per Prescriptive Options Form or Chapter 5 Trade -off calculation form. <br />0 <br />9. Concealed Insulation shall be placed: a) Behind shower/ tub b) Behind partition studs/corner <br />0 <br />10. Standard air leakage (S. 502.4.3) caulking is complete and installed in the following locations: <br />a) Between Sole plate/subfloor d) Partition stud penetrations i <br />b) Wiring/plumbing/duct register penetrations e) Light fixture/flue penetrations <br />c Rim joists mud sills (heated lower floors) f) Around window and door frames <br />0 <br />11. Recessed lighting fixtures (5.502.4.4) shall comply w/one or more of the following: <br />a) IC rated, with no slots or holes in cans, caulked or sealed between can and ceiling. <br />b) IC rated with label certifying an ASI'M E328 tested air leakage:5 2.0 CFM <br />c) Any UL listed fixture enclosed by a r/r" gypboard box or other manufactured box with lfi" <br />clearance to combustibles, and 3" clearance to insulation. <br />Ventilation Requirements for Indoor Air Quality The ventilation and Indoor Air <br />Quality Code (VIAQ) requires that residences be equipped with a means of exhausting pollutants from specific <br />locations. The VIAQ also requires the introduction of fresh air into bedrooms and other habitable spaces. <br />A <br />9 <br />•❑ <br />m uance xe uurea ✓ <br />Ins3ectionApproved ✓ <br />0 <br />12 Source Specific Exhaust Fans: for all bathrooms and laundry areas shall be a minimum <br />of 50 CFM rated at .25 water gauge (w.g.) . Kitchen range hood shall be 100 CFM rated at .10 w.g. <br />A Whole House Ventilation exhaust fart may double duty for bath or laundry fan provided it <br />meets whole house ventilation requirements. Exhaust fans must be ducted to terminate outdoors. <br />0 <br />13. Exhaust fan ducts shall be 2 4" and properly sized (VIAQ, Table 3-3), & insulated to R4. <br />0 <br />14. 0 WHOLE HOUSE VENTILATION- EXiTAUST OPTION <br />0 <br />a) Install a 24 hour timer to control an exhaust fan. <br />0 <br />b) 1.5 sone (quiet) exhaust fan sized (at .25 w.g.) as follows: <br />1-2 bedrooms: 50-75 CFM; 3 bedrooms: 80-120 CFM; <br />4 bedrooms: 100-150 CFM; 5 bedrooms: 120-180 CFM <br />0 <br />c) FRESH AIR INLETS: are required for this option. Inlets are required in all bedrooms and in <br />each habitable room includes bedrooms,kitchen,etc., but not bathrooms or utility rooms <br />15. 0 WHOLE HOUSE VENTILATION - HVAC INTEGRATED OPTION <br />0 <br />a) Install a 24 hour timer to control intake damper and furnace blower. apow <br />0 <br />b) Install an automatic (electric) damper in the outside au intake. Other devices, such as a <br />manual damper or automatic flow regulation device, are only allowed when: airflow is tested <br />or the device is installed as per manufacturers instructions to ensure a whole house air <br />change rate between .35 and .5. <br />0 <br />c) Install a outside air intake duct & connect to return air plenum, within 4' of blower and <br />sized as follows: <br />re SMOOTH Duct Diameters": 6" for 2 bedrooms; 7" for 3 bedrooms; 8" for 4 bedrooms <br />*ADD 1" diameter - for Flex duct; for lengths over 20'; each elbow after 3rd elbow <br />NOTE: The terminal element shall be same size as connecting ductwork or 8", whichever is larger. <br />WSEC Framing Phase Requirements: <br />