Laserfiche WebLink
COMPLIANCE1991 WSEAESIDEAITIAL <br /> REQUIRED <br /> i <br /> INSPECTION <br /> APPROVED IMPORTANT: Please supply information In the shaded boxes end check the appropriate <br /> c:roles. Disregard topics that don't describe your building or equipment. DO-NOI place <br /> checks In the two left columns. <br /> ❑ ❑ ©Exterlor slab Insulation, if not located on the interior, shall be R-10 (fable 6-2). <br /> ❑ ❑ Q Exterior slab Insulation, if present, shall approved for below grade use and protected above grade. <br /> ❑ ❑ QWalls, including riot joists, shXFR <br /> insulated without compression to (Table 6.2): <br /> OR-15 batt (Options 1,11) (Option III, IV, V, VI,VII) <br /> ❑ ❑ interior below grade walls se insulated without compression to (cable 6.2): <br /> QR-15 (Options 1,11) OR-19 (Options III, IV,V,VI,VII) <br /> ❑ ❑ Qo Vaulted ceilings shall be insulated without compression to R-30(Table 6-2, All options) <br /> ❑ ❑ Qi Skyllght wall Insulation is installed and equivalent to the required wall R-values above. <br /> ❑ ❑ r3z Vapor retarders shall be installed toward the warm surface as represented below (502.1.6): <br /> Select one option for floors, walls, and appropriate ceilings: <br /> Floors: 0 Plywood W/exterior glue 0 Poly(> 4 MII) C7 Backed baits <br /> Walls: QQ Poly plastic(2 4 Mil) Q Face-stapled, backed batts ZPVA paint <br /> Ceilings: Not required where ventilation space averages >12"above insulation. <br /> Face stapled backed batte C7Poly plastic (: 4 mil) N�PVA paint <br /> O ❑ QQ Hoating system efficiency and sizing requirements shall be met as represented below: <br /> ED ®Heat Pump efficiency shall be met under the following compliance path (S. 503.4): <br /> O Split system, air source heat pump:HSPF> 6.8, COP>3.0 <br /> O Single package, air source heat pump:HSPF i 6.6, COP >3.0 <br /> 0 Water source heat pump:COP 2 3.8 <br /> 0 Ground source heat pump COP 2 3.0 <br /> ❑ ❑ E Central force-alr furnace AFUE rating, as listed in the LAMA Directory, shall be: <br /> �2 .78 (Options I, 11, IV,VI,VII) O 2 .88 (Option III)) 0;--74 (Option V) <br /> 13 EJQQQ'''ee Noentral, combustion heating systems shall have intermits I ig i ion <br /> El (17 Maximum heating system output (150%of design heat Joao) is BTU/hr. (S. 503.2.2) <br /> ❑ C-] ale High efficiency fc.ced-alr furnace (s 56,000 BTU/hr.output)may may exceed 150%of DHL <br /> because: QGAMA listed AFUE is z 78 + 1 per each 5000 BTU/hr output that it exceeds the DHL. <br /> [SEC Insulatlon phase requirements: — - <br /> Inspected by: Date <br /> ❑ ❑ a Envelc4ipppp��9� Floors shall be insulated without compression, and with supports 24"O.C.to: <br /> R19 (Optlons i, II, III, IV, V) O R25 (Options VI, VII) <br /> ❑ ❑ <br /> (DNon-vifultecl,attic ceilings shall be Insulated without compression to: {{See Table 6-2 <br /> MR-30(Options I, Il, III, IV,V, VII) 0 R @ <br /> 3G (Option VI) ee Ta _.-2 <br /> ❑ QDoor systems shall meet:0U.40 (All options) V — <br /> LDoor types are (1) _(2)_ _(3) <br /> Page 5 of 6 <br />