Laserfiche WebLink
:Component Performance Path, pg. 1 Zones 4c/5b ENV-UA <br /> 2012 Washington State Energy Code Compliance Forms for Commercial Buildings including R2&R3 over 3 stories and all R1 Revised Oct 2013 <br /> Project Address Underwood Gartland - Building A Date 05/18/2015 <br /> Occupancy Group * Commercial O Group R For Building Department Use <br /> Change in occupancy or space conditioning (-) <br /> Note-Proposed UA may exceed Target UA by 10%per C101.4.4 and C101.4.5 <br /> Fenestration Area as%gross above-grade wall area 7.7% Max.Target: 30.0% <br /> Skylight Area as%gross roof area 1.3% Max.Target: 5.0% <br /> Vertical Fenestration Alternates: None Selected on ENV-SUM <br /> Notes: 1:If vertical fenestration or skylight area exceeds maximum allowed per C402.3.1, then Target Area Adjustment of all applicable envelope <br /> elements will be calculated by the compliance form. Refer to Target Area Adjustments worksheet for this calculation. <br /> 2:LI-factors shall come from Appendix A, Chapter C303, or calculated per approved method as specified in C402.1.2. <br /> Building Component Proposed UA Target UA <br /> Provide source of U-factor,page/plan#of assembly detail&ID U-factor x Area(A) =UA(U x A —U-tactor x Area(A)= UA(U x A) <br /> Y R=20.833 ID:Rigid Above Deck 0.048 198080 9507.8 0.034 198080 6734.7 <br /> o R= ID:(R-20 Insultaion Only Per Table 102.2.6) Above Deck Insulation U-0.034 <br /> R= ID: <br /> -p R= ID: 0.031 <br /> C0 R= ID: Metal Building U-0.031 <br /> cr R= ID: <br /> FRID: 0.021 <br /> ID: Single raft,attic,other U-0.021 <br /> ID: <br /> R= ID: 0.055 <br /> 11 R= ID: Steel/metal frame U-0.055 <br /> a� <br /> R= ID: <br /> o a R= ID: 0.052 <br /> C0 R= ID: Metal Building U-0.052 <br /> 2 R= ID: <br /> R= ID: 0.054 <br /> o R= ID: Wood Frame,other U-0.054 <br /> a 3: R= ID: <br /> O <br /> R=11 ID:w/Stick-pin Insulation R-11 (Al 03.3.7.1(2)) 0.081 59587 4826.5 0.104 59587 6197.0 <br /> in <br /> ro R= ID: Mass Wall U-0.104 <br /> R= ID: <br /> D R= ID: 0.104 <br /> m <br /> 0 3 R= ID: Assumed to be Mass Wall U-0.104 <br /> 0_0E5 <br /> M E5R= ID: <br /> C7 R= ID: <br /> N R= ID: 0.031 <br /> U) R= ID: Mass Floor U-0.031 <br /> o R= ID: <br /> R= ID: 0.029 <br /> E R= ID: Joist/Framing U-0.029 <br /> u R= ID: <br /> F-factor x Perimeter =UA(U x A) F-factor x Perimeter= UA(U x A) <br /> R= ID:No Insulation 0.730 2572 1877.6 0.540 2572 1388.9 <br /> CZ <br /> R= ID: Slab-On-Grade U-0.54 <br /> CoC: <br /> R= ID: <br /> 9 R= ID: 0.550 <br /> R= ID: Heated Slab-On-Grade U-0.55 <br /> = R= ID: <br /> "Proposed non-residential CMU walls meeting Table C402.1.2 Area UA Area UA <br /> Footnote D requirements can use the target U-value of 0.104 rather Page 1 <br /> than Appendix A values.Show footnote requirements in plans. Subtotal F260239 16 212 260239 14321 <br /> Component Performance Compliance (UA) UA COMPLIES <br />