5631 HIGHWAY PL 2017-07-12 - Laserfiche WebLink

POTTER P200 Plus 4 Fire Alarm Control Panel Features • 75 Analog Addressable Points.Any combination of'detectors/ modules • 5 Amp Power Supply.Expandable to 315 amps • 2 NAC circuits rated at 3 amps maximum,expandable to 188. • 2 Input/Output(1/0)Circuits for system flexibility rated at I Amp each • Built-in UL Listed IP Communicator • Built-in email event notification and report capability. • Optional Dual Line Digital Alarm Communicator Q • System wide synchronization of Potter/AMSECO,Gentex, Cooper/Wheelock,and System Sensor signals. • No twisted or shielded wiring required. • Cabinet will accommodate up to 18AH batteries.Panel will charge up to 55AH. • Capable of Class A or Class B wiring configurations • Built-in NFPA 72 compliant smoke detector sensitivity test • Dead-front cabinet design • 1000 Event History Buffer Potter/Nohmi Protocol Features • Less than 4 second polling time • LED's visible from 360° • Adjustable Smoke Detector Sensitivity • Adjustable Heat Detector Temperature • HighTemperature Heat Detector as fixed temp UL NYC Fire Dept. • Drift Compensation _ Certificate of Approval • Maintenance Alerts S735 7165-0328:0195 6156 • Day/Night Mode Product includes a S year warranty Description The P200 is a small analog/addressable fire alarm control panel with a and can be mounted 6,500 feet from reach other.P-Link devices such as total of'75 points.The points may be any combination of smoke sensors, the RLY-5 relay module,SPG-1000 serial parallel gateway and DRV-50 heat detectors or modules.This panel has a 5.0 amp power supply that is LED driver can be mounted anywhere in the chain of communication distributed across two Notification Appliance Circuits(NACs). with a maximum of 31 of each P-Link devices. The NAC circuits are rated at a maximum of 3 Amps each.All of The entire system,including the SLC,NACs and P-Link may be the outputs may be configured for notification or auxiliary power.In converted with a CA-6075 Class A module.The entire system is addition,each NAC can be programmed for strobe synchronization and programmed using a Windows based computer software and requires utilizes Quadrasync for strobe synchronization across circuits of various the use of a software programming software key. brands. The P200 can communicate to a monitoring station using the on board The cabinet will hold two 12 volt,8 amp/hour batteries or two 12 volt, Ethernet connection to an 1P communicator or using optional UL listed 18 amp/hour batteries.The system when fully loaded will charge 55 UD-1000 traditional two line alarm communicator.The UD-1000 amp/hour batteries.Anything larger than 18 amp/hour will require an connects to the main board and has two phone line jacks provided. external battery cabinet the SSU-00050. The IP communicator uses a RJ-45 connection and when connected The panel has the Potter P-Link connection for expansion with remote to the internet may be programmed to E-mail system status,history annunciators,intelligent power supplies and other optional modules. reports,reminders and the configuration file.The panel may be updated The P-Link will support 31 accessories in any combination.The RA- remotely using the UD-1000.If the Ethernet connection is needed 6075 is a 2 x 16 LCD annunciator.The RA-6500 offers a larger 4 x remotely,the FCB-1000 fire communication bridge may be installed to 40 line LCD display that allows points and descriptions to be shown allow the Ethernet connection to be installed in a rack. simultaneously.Intelligent remote power supplies repeat the P-Link data Potter Electric Signal Company,LLC • St.Louis,MO 800-325-3936• wwwpottersignal.com PkZ!l:0 #8830034-REV A PAGE 1 OF 4 08/12