2000 TOWER ST OLYMPUS HALL 2017-07-28

gEmacm 2012 Washington State Energy Code Compliance Forms for Commercial,Group R1,and>3 story R2 and R3 Revised June 2013 Project Address 801 Wetmore Ave-EvCC Olympus Hall HVAC Date 1/25/2016 The following information is necessary to check a mechanical permit application for commercial provision compliance with the 2012 WSEC. NOTE:Define print area in Excel prior to printing MECH-CHK pages. Applicability Code Section Code Provision Information Required Location Building Department (yes,no,na) I I on Plans Notes COMPLEX SYSTEMS,CONTINUED Specific System Requirements y C403.4.2& Variable flow control-fans Indicate fans requiring variable flow control and method C403.2.12 MO.2 NA C403.4.2.1 VAV fan static pressure Indicate sensor locations on plans;include at least one sensor per major - sensors duct branch C403.4.2.2 VAV fan static pressure Indicate fan system static pressure setpoint based on zone requiring most NA setpoint pressure - VAV systems serving multi- Indicate supply air systems serving multiple zones that are required to be C403.4.5 VAV,method of primary air control,and zones served;note exceptions NA zones taken MO.2 y C403.4.5.4 VAV system supply air reset Indicate controls that automatically reset supply air temp in response to MO.1 loads NA C403.4 Large capacity cooling Indicate method of multi-stage or variable control for building cooling systems system capacity>300 tons NA C403.4.7 Hot gas bypass limitation Indicate cooling equipment unloading or capacity modulation method _ y C403.4.3 Large capacity boiler Indicate multi-stage or modulating burner for single boilers>500,000 btuh systems MO.2 y C403.4.3 Boiler sequencing Indicate automatic controls that sequence operation of multiple boilers MO.2 C403.4.3.5 Chiller/boiler plant pump Indicate capability to automatically reduce overall plant flow and shut-off y isolation flow through chillers&boilers when not in use MO.2 C403.4.2& Variable flow control- Indicate pumps requiring variable flow control&method y C403.4.3.6 pumps MO.2 NA C403.2.12.1 Variable flow control- Indicate cooling tower fans requiring variable flow control and method _ &C403.4.4 cooling towers C403.4.3.4 Hydronic system part load reset supply water tem AND reduce flow b >50%fors stems>300,000 y controls PP y P y- y Mo.1 NA C403.4.3.2Two-pipe changeover Indicate deadband,heating/cooling mode scheduling and changeover systems temperature range NA C403.4.3.3.1 Water loop heat pump- Indicate capability of central equipment to provide min.20°F water supply deadband temp deadband between heat rejection and heat addition modes NA C403.4.3.3 Water loop heat pump- Provide heat exchanger that separates cooling tower and heat pump loop - heat rejection in Climate Zone 5 NA C403.4.3.3.3 Water loop heat pump- Indicate 2-way isolation valve on each heat pump and variable flow control - isolation fors stems with total pump power>10 h NA C403.4.6 Condenser water heat Indicate system provided to pre-heat service water and efficiency _ recovery N A C403.5 Cooler/freezer-anti-sweat Indicate w/sf&control method for walk-in cooler/freezer door anti-sweat - heaters I heaters NA C403.5/6 Cooler/freezer-evaporator Indicate motor type for evaporator and condenser fans<1 hp - a dco n rfans SERVICE WATER HEATING Service Water Systems NA C404.2 Water-heating equip min. Provide equipment schedule or complete MECH-SUM table with type, efficiency capacity,efficiency,test standard or other efficient source NA C404.3 Temperature controls Indicate temperature controls have required setpoint capability N A C404.4 Heat traps Indicate piping connected to equipment have heat traps on supply& discharge NA C404.5 Insulation underwater Indicate R-10 insulation under tank _ heater NA C404.6 Service water piping Indicate R-value of insulation on piping;note exceptions taken insulation C404.7/8 Circulation systems and Indicate shut-off capability based on occupancy and periods of limited NA heat trace shut-off demand _ NA C404.9 Group R-2 service hot water Indicate method of usage metering for dwell.units served by central HW eters s Pools&In-Ground Permanently Installed Spas Pool heating equip min. Provide equipment schedule or complete MECH-SUM table with type, NA C404.10.1 efficiency capacity,efficiency,test standard(or other eff.source);heat pump heaters >_4 COP NA C404.10.1/2 Pool heater on/off controls Indicate automatic on/off control based on scheduling&accessible on/off switch on heater that operates independent of thermostat setting;or NA C404.10.3 Pool covers Indicate vapor retardant cover and insulation rating as required _ NA C404.10.3 Pool assembly insulation Indicate rating of insulation on sides and bottom of pools heated to>90°F NA L.C404.10.4 Heat recovery Indicate method,exhaust air temperature reduction and recovered energy - us