840 N BROADWAY 2017-08-21 - Laserfiche WebLink

TABLE C407.5.1(4) SPECIFICATIONS FOR THE STANDARD REFERENCE DESIGN HVAC SYSTEM DESCRIPTIONS ° SYSTEM NO. SYSTEM TYPE FAN CONTROL COOLING TYPE HEATING TYPE I Variable air volume with parallel fan-powered VAV Chilled water' Electric resistance boxes' 2 Variable air volume with reheath VAVd Chilled water' Hot water fossil fuel boilerf 3 Packaged variable air volume with parallel VAVd Direct expansion' Electric resistance fan-powered boxeSa 4 Packaged variable air volume with reheatb VAVd Direct expansion' Hot water fossil fuel boiler 5 Two-pipe fan coil Constant volume Chilled water' Electric resistance 6 Water-source heat pump Constant volume', Direct expansion' Electric heat pump and boilers 7k Four-pipe fan coil Constant volume'j Chilled water' Hot water fossil fuel boilerf 8k Packaged terminal heat pump Constant volume'•] Direct expansion' Electric heat pump 9k Packaged rooftop heat pump Constant volume'' Direct expansion' Electric heat pump h lok Packaged terminal air conditioner Constant volume'•] Direct expansion Hot water fossil fuel boilerf Ilk Packaged rooftop air conditioner Constant volume'' I Direct expansion Fossil fuel furnace ■ For SI: 1 foot=304.8 mm,1 cfm/ftz=0.0004719,1 Btu/h=0.293/W,'C=[('F)-32/1.8]. a. VAV with parallel boxes:Fans in parallel VAV fan-powered boxes shall be sized for 50 percent of the peak design flow rate and shall be 0 modeled with 0.35 W/cfm fan power.Minimum volume setpoints for fan-powered boxes shall be equal to the minimum rate for the space required for ventilation consistent with Section C403.4.4,Exception 4.Supply air temperature shall be reset based on zone demand.Design C airflow rates shall be sized for the maximum reset supply air temperature.The air temperature for cooling shall be reset higher by 5'F under the C minimum cooling load conditions. b. VAV with reheat:Minimum volume setpoints for VAV reheat boxes shall be 0.4 cfm/ft2 of floor area.Supply air temperature shall be reset ° based on zone demand.Design airflow rates shall be sized for the maximum reset supply air temperature.The air temperature for cooling shall be '1 reset higher by 5°F under the minimum cooling conditions. o� C. Direct expansion:The fuel type for the cooling system shall match that of the cooling system in the proposed design. d. VAV:When the proposed design system has a supply,return or relief fan motor horsepower(hp)requiring variable flow controls as required by Section C403.2.11.5,the corresponding fan in the VAV system of the standard reference design shall be modeled assuming a variable speed drive.For smaller fans,a forward-curved centrifugal fan with inlet vanes shall be modeled.If the proposed design's system has a direct digital control system at the zone level,static pressure setpoint reset based on zone requirements in accordance with Section C403.4.I shall be modeled. ° e. Chilled water:For systems using purchased chilled water,the chillers are not explicitly modeled.Otherwise,the standard reference design's chiller plant shall be modeled with chillers having the number as indicated in Table C407.5.1(5)as a function of standard reference building chiller plant load and type as indicated in Table C407.5.1(6)as a function of individual chiller load.Where chiller fuel source is mixed,the system in the standard reference design shall have chillers with the same fuel types and with capacities having the same proportional capacity as the proposed design's chillers for each fuel type.Chilled water supply temperature shall be modeled at 44'F design supply temperature and 56°F return temperature.Piping losses shall not be modeled in either building model.Chilled water supply water temperature shall be reset in accordance with Section C403.4.2.4.Pump system power for each pumping system shall be the same as the proposed design;if the proposed design has no chilled water pumps,the standard reference design pump power shall be 22 W/gpm(equal to a pump operating against a 75-foot head,65-percent combined impeller and motor efficiency).The chilled water system shall be modeled as primary-only variable flow with flow maintained at the design rate through each chiller using a bypass.Chilled water pumps shall be modeled as riding the pump curve or with variable-speed drives when required in Section C403.4.2.4.The heat rejection device shall be an axial fan cooling tower with variable speed fans if required in Section C403.4.3.Condenser water design supply temperature shall be 85°F or 10°F approach to design wet-bulb temperature, C whichever is lower,with a design temperature rise of 10'F.The tower shall be controlled to maintain a 70'F leaving water temperature where weather permits,floating up to leaving water temperature at design conditions.Pump system power for each pumping system shall be the same as 1 the proposed design;if the proposed design has no condenser water pumps,the standard reference design pump power shall be 19 W/gpm(equal to a pump operating against a 60-foot head,60-percent combined impeller and motor efficiency).Each chiller shall be modeled with separate condenser water and chilled water pumps interlocked to operate with the associated chiller. f. Fossil fuel boiler:For systems using purchased hot water or steam,the boilers are not explicitly modeled.Otherwise,the boiler plant shall use the same fuel as the proposed design and shall be natural draft.The standard reference design boiler plant shall be modeled with a single boiler if the standard reference design plant load is 600,000 Btu/h and less and with two equally sized boilers for plant capacities exceeding 600,000 Btu/h. Boilers shall be staged as required by the load.Hot water supply temperature shall be modeled at 1807 design supply temperature and 130°F return temperature.Piping losses shall not be modeled in either building model.Hot water supply water temperature shall be reset in accordance with Section C403.4.2.4.Pump system power for each pumping system shall be the same as the proposed design;if the proposed design has no hot water pumps,the standard reference design pump power shall be 19 W/gpm(equal to a pump operating against a 60-foot head,60-percent combined impeller and motor efficiency).The hot water system shall be modeled as primary only with continuous variable flow.Hot water pumps shall be modeled as riding the pump curve or with variable speed drives when required by Section C403.4.2.4. CE-104 2015 Washington State Energy Code