2222 EVERETT AVE 2017-08-10 - Laserfiche WebLink

Wiring & Configuration Signature device loop Auxiliary&smoke power outputs(TB3) The system provides one Signature device loop circuit with a total The control panel provides two auxiliary power TB3 capacity of 125 detectors and 125 module addresses.The loop outputs that can be used for powering ancillary NO circuit is supervised for opens,shorts,and grounds. equipment such as remote annunciators and two (1) Circuit 'L� wire smoke detectors. Aux 2 can be software NC i01000 1064 selected to operate continuously.The circuit is specifications Device loops One Class B or A One Class B or A loop, supervised for shorts and grounds. loop,supporting 125 supporting 64 devices of (2) 0 NO Circuit s detectors and 125 any kind. specifications modules.Expandable to Circuit voltage 21.9 to 28.3 V range NC four loops. Resettable circuit 24 VDC nominal at 500 mA (3) Communication Maximum 20 V peak-to-peak (Aux power 2) NO line voltage Continuous circuit 24 VDC nominal at 500 mA. Circuit current 0.5 A max (Aux power 1) Use this circuit for powering Q Circuit 660 total,0.5 uF,max two-wire smoke detectors. (4) P Isolators 64 maximum Note:Any current above 0.5 amp connected to both Aux 1 and 2 will reduce the total available NAC power by that Signal Supported on a system-wide basis(all device loops) amount. Synchronization when using a SIGA-CC1 S or SIGA-MCC1 S module (1)Trouble and Genesis or Enhanced Integrity notification ap- Alarm trouble and supervisory Perviso rY rela Y(TB3)) (2)Supervisory The trouble relay is normally-open, held closed, (3)Alarm Class Bwiring Class A wrong and opens on any trouble event or when the panel is de-energized.The supervisory relay is (4)Smoke/Aux SLC A Dae Lne SLC A +� normally-open,and closes on any supervisory event.The alarm relay changes over on any SLC B SLC B +� alarm event. Loop Loop Loop Loop Loop card devke device Loop cartl Dab Line devke devke Relay specifications I Alarm Trouble Supervisory Type Form C Form A Notification appliance circuits(TB2) Voltage 24 VDC at 1 A resistive 24 VDC at 1 A resistive i01000 control panels come equipped with four notification ap- Relay circuits can only be connected to power-limited sources. pliance circuits. i064 control panels come with two NACs. Each circuit can be individually configured for continuous,temporal, synchronized,and coded output. Annunciator loop(TB4) Specifications i01000 iO64 The control panel provides a connection for up to eight serially Circuit Type — 4 Class B or 2 Class A 2 Class B or 2 Class A driven and supervised remote annunciators. with SA-CLA module Voltage 24 VFWR Circuit specifications Current 6.0 A total,2.5 A max. 3.75 A total,2.5 A max. Device loops Class B(Style l)or Class A(Style 2) per circuit at 120/230 per circuit at 120/230 Circuit voltage 2.55 V VAC 60 Hz. VAC 60 Hz. Circuit current 30 mA max 5.0 A total,2.5 A max. 3.0 A total,2.5 A max. Circuit Up to 8 annunciators or 4000 feet per circuit at 230 VAC per circuit at 230 VAC impedance 50 Hz. 1 50 Hz. Impedance 26 0 total,0.35 uF max Class B Class A EOLR 15 K 0,Y2 W Channell Channell Channell Channell Synchronization Supported system-wide + — + — + — + — � T64 � 751 T84 0-8--g Class A wiring Annunciator Annunciator e NAC1- + + ee _- _- 0 NAC1- TTTT +- -+ CH (+)IN CHI(-)IN NAC1+ ACI- 0 CH1(-)IN CHI(-)IN NAC2- + EOLR 2 + + NAC2+ - - CH2(+)IN &CH2(+)IN T� NAC3- + + T132- (S)CH2(-)IN CH2(-)IN NAC3+ - - + NAC4- EOLR e - NAC4+ - + ' B T86 Marking indicates output signal polarity when the circuit is active.Polarity reverses when the circuit is not active.Wire notification appliances accordingly.Notification appliance polarity shown in active state. Page 4 of 8 E85001 -0135 Issue 1.1