2222 EVERETT AVE 2017-08-10 - Laserfiche WebLink

Option Cards EDWARDS iO Series panels are supported by a complete line RZI16-2 Remote Zone Interface Module of modules and related equipment that enhance performance I-W and extend system capabilities.Option cards plug directly into the control panel main circuit board or are connected to it with a ribbon cable.After installation,terminals remain accessible.The - cabinet provides ample room for wire routing,keeping wiring neat at all times. f� Single and Dual Loop Controller Cards The RZI16-2 Addressable Remote Zone Interface Module is an The iO-SDC1 is a single loop controller card that can be used with addressable device that provides connections for sixteen Class B the i064 as a replacement for the standard 64-point loop,or with Initiating Device Circuits and two Class B Supervised Output the i01000 as a 250-point expansion module. Circuits.The inputs and outputs can be configured individually for The iO-SDC2 is a 500-point dual loop controller card for the several device types. iO1000 that provides two SLC circuits, each with 125 detector It requires 18 consecutive addresses on the Signaling Line Circuit addresses and 125 module addresses. (SLC).Addresses are assigned electronically.There are no address Specifications i0-SDC1 iO-SDC2 switches to set. Device Addresses i01000:one loop,250 i01000:two loops, The RZI16-2 incorporates two 8-segment DIP switches that are device addresses 500 device addresses used to select the Alarm or Supervisory default device type for i064:64 addresses each of the 16 IDC circuits.The module also includes one 4-seg- Wiring Class B or Class A ment DIP switch used to select the default Relay or NAC output Operating Voltage 24 VDC device type. Device types other than the default are accomplished Operating Current Standby:55 mA Standby:45 mA through programming. (fully loaded loop) Alarm:80 mA Alarm:70 mA Note:These ratings do not include the use of two-wire smoke modules. RZI16-2 Specifications m Communication Line Max.20.6 V peak-to-peak Voltage Voltage 24V/Aux nominal: 24 VDC Terminal Rating 12 to 18 AWG(0.75 to 2.5 mmg Supervisory current: 250 mA at 24 VDC nominalAlarm Current 1000 mA Circuit Current 0.5 A max. 24V/Aux minimum: 18.4 VDC Max total loop 66 f) 24V/Aux maximum: 26.4 VDC resistance NAC1,NAC2 nominal: 24 VDC Max total loop 0.5 pF Current capacitance Standby current Isolators 64 isolators maximum per loop(total both for 4.7 k EOL(U.S.) 4.8 mA/circuit isolator bases and modules) Standby current for Ground Fault 0 to 5 kQ 3.9 k EOL(Canada) 5.7 mA/circuit Impedance Alarm current Operating 32 to 120°F(0 to 49°C) at nominal voltage 31.1 nrA/circuit Environment 0 to 93%noncondensing at 90°F(32°C) Relay outputs Quantity 2 Type Rating(pilot duty) Programmable 24 VDC at 2.5 A Input circuit wiring 25 Q per wire SA-ETH Ethernet Interface Card resistance SA-ETH wiring The SA-ETH card provides a Initiating device circuits etAork New,ork cable—& ro` on standard 10/100 Base T Ether- Quantity 16 NeUnork ca 61e connnecec tion net network connection for EOL resistor 4.7 kQ(U.S.);3.9 kQ Canada connecting to an intranet, a local Zone voltage 22.78 V for 4.7 kQ(U.S.) I network, or the Internet.The 22.08 V for 3.9 kQ(Canada) + card can be used to download Alarm current 31.1 mA/channel at nominal voltage Alarm impedance range <680 Q a configuration programming from Trouble impedance range >5.55 kQ the iO-CU to the panel. Supervised output circuits The Ethernet card is installed on EOL resistor 15 kQ ® the plastic assembly and con- Quantity 2 � Short circuit detection <2.6 kQ nects to the main circuit board Open circuit detection >61.9 kQ Ethemetcard via a ribbon cable. Contact ratings 24 VDC at 2.5 A(5 A for two NACs) SA-ETH specifications Compatible cabinets MFC(A),i01000,APS Ethernet 10/100 Base T Operating environment Temperature 32 to 120°F(0 to 49°C) Humidity 0 to 93%RH,noncondensing at 90°F (32°C) Page 5 of 8 E85001 -0135 Issue 1.1